bass fishing – Transducer Shield and Saver

Showing 1–30 of 41 results

In Stock

“The Wedge” – Trolling Motor Shallow Water Bracket

Let’s Fish Shallow with “The Wedge”. No more holding the trolling motor rope to fish shallow.
Simply place “The Wedge” beneath the trolling motor bracket and GO SHALLOW.
Available to fit Garmin Force, Lowrance Ghost, Minnkota Ultrex and Fortrex or Motorguide Pro Tour.

Price range: $114.95 through $134.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

TS-AIHD-TS Combo fits Lowrance® ActiveImaging HD™ transducer # 000-16062-001 or ActiveImaging HD™ FishReveal transducer # 000-16060-001 on a trolling motor

^{Item # TS-AIHD-TS Combo}^{is built in High Quality Aluminum Alloy and Black Powder Coated for Trolling Motor installation. It is designed to fit Lowrance® ActiveImaging HD™ transducer # 000-16062-001 or ActiveImaging HD™ transducer # 000-16060-001. The transducer is approx. 10-1/4” long x 2” wide x 1-1/2″ thick and the cable comes out on top near the back.}

^{It is very important that you complete the questionnaire when ordering our products. The information you provide will help us to assist you better and avoid a delay in shipping your order.}

$225.95

Select options
In Stock

TS-DSS3-TS to fit Lowrance®Total Scan, Structure Scan 3D and HDS Live xDucer 2-in-1 or 3-in-1 on Jack Plate, Hole Shot or Transom Set Back

Choose this item for Jack Plate, Hole Shot Plate or Set Back installation to attach a Lowrance®/Simrad® Total Scan transducer # 000-12568-001 or Lowrance®/Simrad® Structure Scan 3D transducer # 000-12396-001 on a Jack Plate or Transom Set Back. This Transducer Shield will also fit the New Lowrance HDS LIVE Active Imaging 2-in-1 transducer # 000-14490-001 and 3-in-1 transducer # 000-14489-001. NOTE: this item DOES NOT fit the ActiveImageing HD 3-in-1 Transducer # 000-16062-001 or ActiveImaging HD 3-in-1 FishReveal Transducer # 000-1060-001.

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

For trolling motor installation go to TS-DSS3-TS-COMBO.
It is VERY IMPORTANT that you complete the questionnaire when ordering this product.

$189.00

Select options
In Stock

TS-DSS3-TS Combo fits Lowrance® Total Scan & Live Active Imaging 2-in-1 or 3-in-1 xDucer on a Trolling Motor

Choose this item to attach a Lowrance® Total Scan transducer # 000-12568-001 on a Trolling Motor. This Transducer Shield will fit the Lowrance Live Active Imaging transducer # 000-14490-001 or 3-IN-1 transducer # 000-14489-001 NOTE: this item DOES NOT fit the ActiveImage HD 3-in-1 # 000-16062-001 or the ActiveImage HD 3-in-1 FishReveal Transducer # 000-16060-001 It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item.

$215.95

Select options
In Stock

TS-TRI-SH to fit Lowrance Hook 2 / Reveal Triple Shot Transducer # 000-14029-001 on Jack Plate, Hole Shot Plate or Set Back

^{Choose this item to attach a Lowrance® Hook2 / Reveal Triple Shot Transducer # 000-14029-001 for Jack Plate, Hole Shot Plate or Transom Set Back. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item. This Transducer Shield will NOT fit the latest Lowrance Triple Shot transducer # 000-16285-001}
^{NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.}

$189.00

Select options
In Stock

TS-TRI-SH combo to fit Lowrance Hook 2 / Reveal Triple Shot xDucer 000-14029-001 on Trolling Motor

_{Choose this item to attach a Lowrance® Hook2 / Reveal Triple Shot Transducer # 000-14029-001 on a Trolling Motor. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item. This Transducer Shield will NOT fit the latest Lowrance Triple Shot Transducer # 000-16285-001}

$215.95

Select options
In Stock

TS-SP-SH to fit Lowrance® Hook2 Split Shot transducer 000-14028-001 & Eagle Splitshot HD 000-16284-001.

Fits Lowrance® Hook² Split Shot transducer 000-14028-001 It can be attached to a trolling motor, to the side of a Jack Plate with an L Bracket, or on a hole shot plate (under the jack plate) with a Wedge. This Transducer Shield will NOT fit the latest Lowrance Split Shot transducer # 000-16284-001

$89.95

Select options
In Stock

ATLAS 8″ to 12″ Jack Plate – R3 (w/ offset) – for STARBOARD or DRIVER side

L Bracket with 3 inch offset to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ or 12″ Jack Plate. Also available for the Port Side. It is very important that you complete the questionnaire when ordering this item.you

$79.95

Select options
In Stock

ATLAS 8″ to 12″ Jack Plate – L3 (w/ offset)- PORT or PASSENGER SIDE

L Bracket with 3 inch offset to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ or 12″ Jack Plate. Also available for the Port Side. It is very important that you complete the questionnaire when ordering this item.you

$79.95

Select options
In Stock

Atlas 4″ Jack Plate – L Bracket # LB-AT-4-Combo (with solid spacer)

L Bracket – Combo with Solid Spacer to attach a Transducer Shield to the side of an Atlas Hydraulic 4” Jack Plate.

It is very important that you complete the questionnaire when ordering this item.
The information you provide will help us to assist you better and avoid a delay in shipping your order.

$96.95

Select options
In Stock

ATLAS 8″ to 14″ Jack Plate : L Bracket # LB-AT-4.6.8.10.12 (without offset)

L Bracket to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ and 12″ Jack Plate. PLEASE make sure that your jack plate size and Transducer Shield is listed in the description to the left. The larger transducers require our L Bracket with an “offset” or “spacer” to keep the trim rod from hitting the transducer.

It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

$49.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

6/8/10 inch BOB’S Machine Jack Plate – for STARBOARD side

LB-BM-6.8.10 Fits 6″, 8″ & 10″ Bob’s Hydraulic Jack Plates. Used to attach a Transducer Shield to the side of the jack plate.

It is very important that you complete the questionnaire when ordering this product. The information that you provide will help us to assist you better and avoid a delay in shipping your order. The more information that we have about your boat and jack plate, the better we can assist you.

Contact us if you need further assistance.

$59.95

Select options
In Stock

EXT-2.O” Extension

An extension between an L Bracket & Transducer Shield to lower the transducer so as to avoid side viewing signal interference with hull turning chines.

$35.00

Add to cart
In Stock

EXT-1.5″ Extension

Aluminum 1.5″ Extension attached to an L. Bracket and Transducer Shield to lower the level of the transducer. This item is sometimes required on Skeeter & Bass Cat boats.

$35.00

Add to cart
In Stock

EXT-3.0 Extension

Aluminum extension attached between an L Bracket and Transducer Shield will lower the transducer if turning chines or trim tabs interfere with transducer side signal

$40.00

Add to cart
In Stock

HW-Bracket-2 to attach a Hydro Wave speaker box to a Minnkota, Motorguide or Power Pole trolling motor shaft

High Quality Aluminum Bracket to securely attach a Hydro Wave Speaker Box to a trolling motor shaft.

Please complete the questionnaire when ordering this item.

It is VERY important that we know if your trolling motor is an MINNKOTA “ULTREX”

$39.95

Select options
In Stock

Hydro Dynamics Rapid Jack

L. Adapter Bracket to fit Hydro Dynamics Rapid Jack jack plate. Used with a Transducer Shield to attach transducer to the side of the Jack Plate.

^{It is very important that you complete the questionnaire in full when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.}

$49.95

Select options
In Stock

LB-3-RW Blank L. Bracket – STARBOARD side

L. Bracket without pre-drilled holes used on T-H Marine Manual and Pro Hi Jacker 6, 8, 10 and 12″ jack plates

$49.95

Select options
In Stock

LB-AT-4.6.8.10.12 to attach a Transducer Shield to ATLAS 8″ to 12″ jack plates

L Adaptor Bracket used to install a Transducer Shield to the side of an Atlas 8″, 10″ & 12″ Hydraulic Jack Plates

$49.95

Select options
In Stock

LB-SS-4-L to attach a Transducer Shield to Sea Star 4″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 4″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-SS-4-R to attach a Transducer Shield to Sea Star 4″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 4″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-SS-6-8-10-12-L to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 6″, 8″, 10″ or 12″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-SS-6-8-10-12-R to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 6″, 8″, 10″ or 12″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-CMC-5/5-8 to fit 5.5 to 8″ CMC Jack Plate

L Bracket to attach a Transducer Shield to the side of a CMC jack plate.

It is very important that you complete the questionnaire when ordering this item.
The information you provide will help us to assist you better and avoid a delay in shipping your order.

$64.95

Select options
In Stock

LB-DETW-6.8.10 – L Bracket to attach a Transducer Shield to a Detwiler Jack Plate

L Bracket used to attach a Transducer Shield to the side of Detwiler 6″, 8″ or 10″ Jack Plate.

Please complete the questionnaire when placing your order. The more information that we have about your boat and jack plate, the better we can assist you. Contact us if you need further assistance.

$64.95

Select options
In Stock

LB-SM-10/12 for Slidemaster 10″ or 12″ Jack Plate

L Adaptor Bracket to attach a Transducer Shield on the side of a 10″ & 12″ Slide Master Jack Plate. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item.

$49.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

LB-SM-6/8 for Slidemaster 6″ or 8″ Jack Plate

L. Adapter Bracket to fit Slide Master 6″ and 8″ manual Jack Plate. Used to attach a Transducer Shield to the side of the jack plate.

It is VERY IMPORTANT that you complete the questionnaire in full when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

$49.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

LWG-2 Wedge for Hole Shot or Set Back install

LWG-2 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Jack Plate hole shot plate.

$19.95

Select options
Out Of Stock

Rite Hite L Bracket LB-RH-6

Rite Hite L Bracket without an Extender Plate is used when both pieces of the jack plate are at the same at the bottom of the jack plate.
Rite Hite L Bracket with an Extender Plate is used when the engine side piece of the jack plate is lower than the transom piece at the bottom.
Enlarge the jack plate pictures to determine which set up you will need.

Not sure what you need….. call 334-514-7147 or email a good side view photo of your jack plate showing the level of the bottom of the jack plate to: [email protected]

Price range: $54.95 through $103.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

TM-AM-TM150-T to fit Airmar Transom transducer on Trolling Motor

Transducer Shield # TM-AM-TM150T to fit Airmar transom style transducer TM150-T onto a Trolling Motor. Please complete the questionnaire when ordering this item.

If your Airmar transducer can be taken apart to remove the pod from inside the casing, then this is not the Transducer Shield for you.

$149.00

Select options

CLOSE

My Account
Search

Search for:
0