Showing 91–120 of 148 results
-
LWG-2 Wedge for Hole Shot or Set Back install
LWG-2 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Jack Plate hole shot plate.
-
LWG-3 Wedge for Hole Shot or Set Back install
LWG-3 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Hole Shot Plate under a Jack Plate.
-
MG-GS-P1 Grass Shredder Plate to fit Motorguide® trolling motors
Cut through the grass and weeds when fishing in grassy areas. Stainless Steel and Black Powder Coated. Pictures are shown unpainted for easy viewing.
Customer Comment: I want to let you know how much I love my newly purchased Grass Shredder for my MinnKota Fortrex. I installed it as per the instructions and headed out to the Potomac River for a two day club tourney. The Shredder was awesome in all that grass and helped save my batteries. I did not once have to stop and clean the grass off of my trolling motor. To top it all off, I won the event with 10 bass for 23.88 lbs. and caught the biggest Snakehead of my fishing career. The buff was a pleasant surprise and greatly appreciated as I have had 12 skin cancers removed from my head and neck over the years…Thank you, thank you!
-
Mini Receiver Ring Garmin Force Trolling Motor
The Receiver Ring System is designed to allow the attachment of up to three Transducer Shield & Saver product accessories to your trolling motor. We offer a Full or Mini Receiver Ring to fit Garmin Force, Lowrance Ghost or Minnkota Ultrex trolling motors. Coming soon for Motorguide.
The Receiver Ring securely bolts under the trolling motor head for easy accessory attachments.
Check out the additional T S & S product accessories available to attach to our Receiver Ring system:
* ACC-RR-360 is designed for the Humminbird 360
* ACC-TL is designed for the Humminbird TargetLock
* Fish Sniff Fiber Pole is designed for any of the “forward facing transducers”
* Offering three different size Accessory Plates to attach to the Receiver Ring System: ACC-5.1 or ACC-3.5 or ACC-2.5
The Receiver Rings and Accessories are built in 6061 x 3/4″ thick aircraft aluminum alloy, black powder coated and include stainless steel bolts, washers and lock nuts
Proudly Designed and Built in Alabama USA
See More Fish ………. Catch More Fish
-
Mini Receiver Ring Lowrance Ghost Trolling Motor
The Receiver Ring System is designed to allow the attachment of up to three Transducer Shield & Saver product accessories to your trolling motor. We offer a Full or Mini Receiver Ring to fit Garmin Force, Lowrance Ghost or Minnkota Ultrex trolling motors. Coming soon for Motorguide.
The Receiver Ring securely bolts under the trolling motor head for easy accessory attachments.
Check out the additional T S & S product accessories available to attach to our Receiver Ring system:
* ACC-RR-360 is designed for the Humminbird 360
* ACC-TL is designed for the Humminbird TargetLock
* Fish Sniff Fiber Pole is designed for any of the “forward facing transducers”
* Offering three different size Accessory Plates to attach to the Receiver Ring System: ACC-5.1 or ACC-3.5 or ACC-2.5
The Receiver Rings and Accessories are built in 6061 x 3/4″ thick aircraft aluminum alloy, black powder coated and include stainless steel bolts, washers and lock nuts
Proudly Designed and Built in Alabama USA
See More Fish ………. Catch More Fish
-
Mini Receiver Ring Minnkota Ultrex Trolling Motor
The Receiver Ring System is designed to allow the attachment of up to three Transducer Shield & Saver product accessories to your trolling motor. We offer a Full or Mini Receiver Ring to fit Garmin Force, Lowrance Ghost or Minnkota Ultrex trolling motors. Coming soon for Motorguide.
The Receiver Ring securely bolts under the trolling motor head for easy accessory attachments.
Check out the additional T S & S product accessories available to attach to our Receiver Ring system:
* ACC-RR-360 is designed for the Humminbird 360
* ACC-TL is designed for the Humminbird TargetLock
* Fish Sniff Fiber Pole is designed for any of the “forward facing transducers”
* Offering three different size Accessory Plates to attach to the Receiver Ring System: ACC-5.1 or ACC-3.5 or ACC-2.5
The Receiver Rings and Accessories are built in 6061 x 3/4″ thick aircraft aluminum alloy, black powder coated and include stainless steel bolts, washers and lock nuts
Proudly Designed and Built in Alabama USA
See More Fish ………. Catch More Fish
-
MK-Filler Block used to attach a Transducer Shield to a MinnKota Ultrex 36 volt
Item # MK-UL-36-DI-Filler this item is used to attach a Transducer Shield to a 24v or 36v Minnkota “Ultrex” trolling motor with a built in Down Image transducer.
For 36 volt includes two 4.0” and one 6″ heavy duty stainless steel black powder coated straps.
This item must be attached to a Transducer Shield (sold separately) in order for this item to work on the trolling motor. After ordering the Filler, please Click on Shields to choose the correct Transducer Shield to suit your transducer.
Proudly Designed and Built in US
-
MK-GS-P1 Grass Shredder Plate to fit Minnkota 24v 74lb up to 36v 101lb trolling motors
Cut through the grass and weeds when fishing in grassy areas. Stainless Steel and Black Powder Coated. Pictures are shown unpainted for easy viewing.
Customer Comment: I want to let you know how much I love my newly purchased Grass Shredder for my MinnKota Fortrex. I installed it as per the instructions and headed out to the Potomac River for a two day club tourney. The Shredder was awesome in all that grass and helped save my batteries. I did not once have to stop and clean the grass off of my trolling motor. To top it all off, I won the event with 10 bass for 23.88 lbs. and caught the biggest Snakehead of my fishing career. The buff was a pleasant surprise and greatly appreciated as I have had 12 skin cancers removed from my head and neck over the years…Thank you, thank you!
-
MK-GS-P2 Grass Shredder Plate to fit Minnkota 36v 112lb Trolling Motor
Cut through the grass and weeds when fishing in grassy areas. Stainless Steel and Black Powder Coated. Pictures are shown unpainted for easy viewing.
Customer Comment: I want to let you know how much I love my newly purchased Grass Shredder for my MinnKota Fortrex. I installed it as per the instructions and headed out to the Potomac River for a two day club tourney. The Shredder was awesome in all that grass and helped save my batteries. I did not once have to stop and clean the grass off of my trolling motor. To top it all off, I won the event with 10 bass for 23.88 lbs. and caught the biggest Snakehead of my fishing career. The buff was a pleasant surprise and greatly appreciated as I have had 12 skin cancers removed from my head and neck over the years…Thank you, thank you!
-
Quest Trolling Motor Adaptor Plate
Item # Q-A-Plate – Quest Adaptor Plate is built in 6061 High Quality Aluminum Alloy and Black Powder Coated.
About our Adaptor Plate: the Adaptor Plate can be attached to a Transducer Shield which will allow you to attach the Transducer Shield to a Minnkota Quest Trolling Motor so that the clamps / straps are attached to the housing correctly.
About the Minnkota Quest Trolling Motor: the Minnkota Quest housing is configured differently to previous Minnkota models: 1. the skeg is off set; 2. the shaft is larger on the housing; and 3. the US2 sonar is shaped differently to the previous Ultrex trolling motor.
The Good News is – if you already own one of our Transducer Shields simply purchase the Quest Adaptor Plate which will easily attach it to your previously purchased Transducer Shield (TM-H8.3, TG-HG-8.5, TS-AIHD-TS or TS-DSS3-TS).
On the longer TS-DSS3-TS and TS-AIHD-TS Transducer Shields, it will be necessary to purchase an additional component “Ram” to close the gap between the US2 cone and the Transducer Shield. When placing your order, please select the Adaptor Plate with a Ram.
The Quest Adaptor Plate cannot be used with a transducer only; it must be attached to a Transducer Shield.Another Cool Product Proudly Designed in USA
-
Quick Clip
Stainless steel propeller safety clip. Never have to replace that rusted, broken or lost cotter pin again.
-
RAM BT-2 for Humminbird XTM trolling motor transducers
Ram and Strap to fit a Humminbird® trolling motor XTM style transducer. Enlarge photos to identify your transducer. Please complete the questionnaire when ordering this item.
-
Rite Hite L Bracket LB-RH-6
Rite Hite L Bracket without an Extender Plate is used when both pieces of the jack plate are at the same at the bottom of the jack plate.
Rite Hite L Bracket with an Extender Plate is used when the engine side piece of the jack plate is lower than the transom piece at the bottom.
Enlarge the jack plate pictures to determine which set up you will need.Not sure what you need….. call 334-514-7147 or email a good side view photo of your jack plate showing the level of the bottom of the jack plate to: [email protected]
-
SSC-3 fits Humminbird XNT 9 20 T or XNT 14 20 T xDucer on a Trolling Motor
To attach and protect your Humminbird® XNT 9 20 T or XNT 14 20 T (transom style) transducer on a Trolling Motor. (This Transducer Shield will not fit Humminbird Side Image Transducer # XNT 9 SI 180 T. Please see Transducer Shield # TM-CSI)
Please complete the information below when ordering this item.
-
SSC-4 fits Humminbird XP 9 20 (T), XTM 9 20 T or XTM 14 20 T xDucers on a Trolling Motor
Fits Humminbird® Puck Transducer
XP 9 20 (T), XTM 9 20 T or XTM 14 20 T. This shield does not fit any of Humminbird’s side image transducers. -
TM-CSI-2 fits Humminbird Side Image XNT 9 SI 180 T, XNT 9 HW MSI 150 T or XNT 9 QB 90 T xDucer for Trolling Motor, Jack Plate or Set Back
Fits Humminbird® Compact Side Image XNT 9 SI 180T, XNT 9 HW MSI 150 T or Quad Beam XNT 9 QB 90 T transducer
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
TG-D-Vü fits Garmin GT20
To fit Garmin HD ID Down Vu (8 pin) transducer number 010-12087-001 (GT20-TM)
-
TG-DS-9 fits Garmin GT21, GT23, GT41, GT50 and GT51
Ideal for Installing on a trolling motor, on the side of a jack plate or on the boat set back. Additional components will be required. This Transducer Shield will not fit the new Garmin GT 36 or GT 56 transducer.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
It is very important that you complete the questionnaire when ordering this item.
-
TG-DS-Vu to fit Garmin GT30 and GT34
This item is user friendly for various installation options – * Trolling Motor * Side of the Jack Plate * Hole Shot Plate or * Set Back Additional components are required.
When ordering this item, please note in the comment area which transducer you have. Either the Garmin GT30 or GT34 transducer. It is important for us to know this please. This Transducer Shield DOES NOT fit the Garmin GT 36 or GT 56 transducer.NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
TG-TUG to fit Garmin traditional dual beam / dual frequency transducer # 010-10272-00 or 010-10249-20
TG-TUG is Ideal for Installing on a trolling motor. It can also be attached on the side of a jack plate or on the boat set back with additional components.
-
TG-GT30-3D Transducer Shield to fit Garmin DownVü/SideVü GT30 and Pod GT8HW transducers together
Available Now. Transducer Shield to fit Garmin® DownVü/SideVü GT30-TM Transducer and GT8HW-IH pod transducer in tandem on trolling motors.
-
TM-AM-TM150-T to fit Airmar Transom transducer on Trolling Motor
Transducer Shield # TM-AM-TM150T to fit Airmar transom style transducer TM150-T onto a Trolling Motor. Please complete the questionnaire when ordering this item.
If your Airmar transducer can be taken apart to remove the pod from inside the casing, then this is not the Transducer Shield for you.
-
TM-DI fits Humminbird Down Image XNT 9 DI T xDucer for Trolling Motor, Jack Plate or Set Back
TM-DI fits Humminbird® Down Image Transducer # XNT 9 DI T for trolling motor, set back or jack plate installation. It DOES NOT fit the redesigned Down Image transducer # # XNT 9 DI T (RD). Onix Down Image Transducer XNT 14 DI T (RD) or XM 9 MDI T.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
TM-DI-2 fits Humminbird Down Image Xducer # XNT 9 DI T (RD), XM 9 MDI T, Mega XNT 9 HW MDI 75 T or Onix Xducer # XNT 14 DI T (RD) for Trolling Motor, Jack Plate or Set Back
TM-DI-2 fits Humminbird® Down Image Transducer # XNT 9 DI T (RD), XNT 14 DI T (RD) and XNT 9 HW MDI 75 T for trolling motor, set back or jack plate installation. It DOES NOT fit the ORIGINAL Down Image transducer # # XNT 9 DI T.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
TM-HDsi fits Humminbird® HDSI xDucer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T
TM-HDSi fits Humminbird® High Definition Side Image Transducer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T for trolling motor, set back or jack plate installation.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
Garmin Force Rail Kit
$99.95 -
Perspective Mode L Bracket – Garmin Panoptix LiveScope LVS34 transducer on trolling motor shaft or any shaft
Perspective Mode L Bracket Mount used to adjust the position of your Garmin Panoptix LiveScope LVS34 transducer on a trolling motor shaft or any shaft. This item is used along with your Garmin transducer mounting bracket.
-
Ram Rail Kit for small Minnkota Trolling Motors
The Ram Rail Kit includes Skeg, 2 stainless steel straps & hardware. The kit can only be installed on a MinnKota trolling motor that has the Prop & Skeg on opposite ends and when the transducer to be attached is too long for the space between the propeller and skeg.
A transducer cannot be attached directly to the Ram Rail Kit and must be purchased along with a specific Transducer Shield to suit your transducer. After purchasing the Ram Rail Kit, click on “Shields” and choose the Transducer Shield to suit your transducer.
This product can be used with most Humminbird, Garmin & Lowrance Transducer Shields made by Transducer Shield and Saver.
Proudly designed and built in USA
-
TM-XTM-75/150 T to fit Humminbird XTM 9 HW MDI 75 T or XTM 9 HW MSI 150 T transducer
TM-XTM-75/150 T fits Humminbird® Helix Mega Di transducer XTM 9 HW MDI 75 T or Helix Mega Si transducer XM 9 HW MSI 150 T. for trolling motor, set back, hole shot plate or jack plate installation.
If this item is going on a Trolling Motor, please answer the trolling motor questions. If this item is going on the Jack Plate please answer all the questions about your jack plate and boat. It is very important that you answer the questionnaire in full please.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.