Shop – Page 6 – Transducer Shield and Saver

Showing 151–160 of 160 results

“WC 2.5″ x 2.75″ x 0.5″ cable management cover” has been added to your cart. View cart

In Stock

TS-LSS2-L fits Lowrance LSS2 Structure Scan Transducer on a Jack Plate

_{Easily attaches a Lowrance® LSS2 structure scan transducer, with ADDITIONAL components to your Jack Plate or Boat Set Back.}

_{^NOTE^{: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.}}

_{It is VERY IMPORTANT that you complete the questionnaire when ordering this item.}

$169.00

Select options
In Stock

TSS-RM-3D fits Raymarine® RealVision 3D RV100 transducer # A80464
$275.00

Select options
In Stock

WC 2.5″ x 2.75″ x 0.5″ cable management cover

^Black^{polyethylene marine board and is 2-1/2″ x 2-3/4″ x 1/2″ thick and includes stainless steel screws..}

$19.95

Add to cart
In Stock

WG-1 Wedge to attach a Transducer Shield to a Set Back or Hole Shot Plate

WG-1 Wedge along with a Transducer Shield will put the Transducer at the correct angle when the boat is in the water when installed on a Boat Set Back or Jack Plate hole shot/baffle plate

$14.95

Select options
In Stock

WG-3.5 Wedge used to attach TM-HX-1 Transducer Shield to a 90 degree Hole Shot Plate

WG-2.5 Wedge to attach Transducer Shield to 90 degree hole shot plate.

Used along with a Transducer Shield on 90 Degree Jack Plate with Hole Shot Plate. This wedge is suitable for our Humminbird® Transducer Shield # TM-HX-1

$48.95

Select options
In Stock

WG-LSS2 to fit Humminbird TM-HX-3, TM-H8.3 or Garmin TG-HG-8.5 Transducer Shield on Set Back or Hole Shot Plate (10-12″ jack plates only)

Wedge used when attaching a Humminbird® TM-HX-3 or TM-H8.3 Transducer Shield on a boat Set-Back OR on a Hole Shot Plate under a jack plate. This Wedge CANNOT be used on a 90 ° degree Jack Plate.

$47.00

Select options
In Stock

WG-LSS2 to fit Lowrance LSS2, Total Scan, 3-on-1, 2-in-1, Structure Scan 3D Humminbird TM-HX-3 or TM-H8.3 on Set Back or Hole Shot Plate (10-12″ jack plates only)

^{This wedge is used when attaching a Lowrance 10-1/4″ transducer with a Transducer Shield to the Set Back of a Boat – example some Ranger Boats have a good set back.}

$47.00

Select options
In Stock

SBB-HDSI-Combo to attach Humminbird HDSI xDucer XHS 9 HDSI 180 T & Shield on a Transom

Spring Back Bracket and Transducer Shield TM-HDsi combination for transom installation. Ideal for boats with flat transoms or for boats without a jack plate.

$194.95

Select options
In Stock

BLOCK-HDSI for Humminbird Side Image xDucer XHS 9 HDSI 180 T on a Spring Back Bracket for install on a Transom

Block-HDSI will help to prevent the factory bracket from pivoting upward on the transducer-arm when struck by an underwater object. The block is designed specifically for HDSI XHS-HDSI-9-180 T Transducer only.

$9.95

Select options
In Stock

BLOCK-LSS1-2 for Lowrance Structure Scan bracket attached to SBB-4

Block-LSS1-2 will help to prevent the factory bracket from loosening and pivoting upward when struck by an underwater object. The block is designed to fit the original Lowrance factory bracket. Click on the link BELOW to identify your factory bracket. Lowrance LSS1 or LSS2 factory bracket difference

$18.95

Select options

CLOSE

My Account
Search

Search for:
1