SONAR – Transducer Shield and Saver

Showing 1–30 of 33 results

In Stock

AP-SP-SH Armor Plate to fit Lowrance® Hook 2 Split Shot Transducer

For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket. This Armor Plate will NOT fit the latest Lowrance Split Shot transducer # 000-16284-001
It is very important that you complete the questionnaire in full when ordering any of our products.

$79.95

Select options
In Stock

TS-DSS3-TS to fit Lowrance®Total Scan, Structure Scan 3D and HDS Live xDucer 2-in-1 or 3-in-1 on Jack Plate, Hole Shot or Transom Set Back

Choose this item for Jack Plate, Hole Shot Plate or Set Back installation to attach a Lowrance®/Simrad® Total Scan transducer # 000-12568-001 or Lowrance®/Simrad® Structure Scan 3D transducer # 000-12396-001 on a Jack Plate or Transom Set Back. This Transducer Shield will also fit the New Lowrance HDS LIVE Active Imaging 2-in-1 transducer # 000-14490-001 and 3-in-1 transducer # 000-14489-001. NOTE: this item DOES NOT fit the ActiveImageing HD 3-in-1 Transducer # 000-16062-001 or ActiveImaging HD 3-in-1 FishReveal Transducer # 000-1060-001.

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

For trolling motor installation go to TS-DSS3-TS-COMBO.
It is VERY IMPORTANT that you complete the questionnaire when ordering this product.

$189.00

Select options
In Stock

TS-TRI-SH to fit Lowrance Hook 2 / Reveal Triple Shot Transducer # 000-14029-001 on Jack Plate, Hole Shot Plate or Set Back

^{Choose this item to attach a Lowrance® Hook2 / Reveal Triple Shot Transducer # 000-14029-001 for Jack Plate, Hole Shot Plate or Transom Set Back. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item. This Transducer Shield will NOT fit the latest Lowrance Triple Shot transducer # 000-16285-001}
^{NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.}

$189.00

Select options
In Stock

TS-TRI-SH combo to fit Lowrance Hook 2 / Reveal Triple Shot xDucer 000-14029-001 on Trolling Motor

_{Choose this item to attach a Lowrance® Hook2 / Reveal Triple Shot Transducer # 000-14029-001 on a Trolling Motor. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item. This Transducer Shield will NOT fit the latest Lowrance Triple Shot Transducer # 000-16285-001}

$215.95

Select options
In Stock

TS-SP-SH to fit Lowrance® Hook2 Split Shot transducer 000-14028-001.

Fits Lowrance® Hook² Split Shot transducer 000-14028-001 It can be attached to a trolling motor, to the side of a Jack Plate with an L Bracket, or on a hole shot plate (under the jack plate) with a Wedge. This Transducer Shield will NOT fit the latest Lowrance Split Shot transducer # 000-16284-001

$89.95

Select options
In Stock

ATLAS 8″ to 12″ Jack Plate – R3 (w/ offset) – for STARBOARD or DRIVER side

L Bracket with 3 inch offset to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ or 12″ Jack Plate. Also available for the Port Side. It is very important that you complete the questionnaire when ordering this item.you

$79.95

Select options
In Stock

ATLAS 8″ to 12″ Jack Plate – L3 (w/ offset)- PORT or PASSENGER SIDE

L Bracket with 3 inch offset to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ or 12″ Jack Plate. Also available for the Port Side. It is very important that you complete the questionnaire when ordering this item.you

$79.95

Select options
In Stock

Atlas 6″ Jack Plate – L Bracket # LB-AT-6-R3 (with built in offset)

L Bracket to attach a Transducer Shield to the side of an Atlas Hydraulic 6” Jack Plate. The larger transducers require our L Bracket with the built in offset to keep the trim rod from hitting the transducer.

It is very important that you complete the questionnaire when ordering this item.

The information you provide will help us to assist you better and avoid a delay in shipping your order.

$89.95

Select options This product has multiple variants. The options may be chosen on the product page
Out Of Stock

ATLAS 8″ to 12″ Jack Plate : L Bracket # LB-AT-4.6.8.10.12 (without offset)

L Bracket to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ and 12″ Jack Plate. PLEASE make sure that your jack plate size and Transducer Shield is listed in the description to the left. The larger transducers require our L Bracket with an “offset” or “spacer” to keep the trim rod from hitting the transducer.

It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

$49.95

Select options
In Stock

EXT-2.O” Extension

An extension between an L Bracket & Transducer Shield to lower the transducer so as to avoid side viewing signal interference with hull turning chines.

$35.00

Add to cart
In Stock

EXT-3.0 Extension

Aluminum extension attached between an L Bracket and Transducer Shield will lower the transducer if turning chines or trim tabs interfere with transducer side signal

$40.00

Add to cart
In Stock

Hydro Dynamics Rapid Jack

L. Adapter Bracket to fit Hydro Dynamics Rapid Jack jack plate. Used with a Transducer Shield to attach transducer to the side of the Jack Plate.

^{It is very important that you complete the questionnaire in full when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.}

$49.95

Select options
In Stock

LB-3-LW Blank L. Bracket – for PORT SIDE

L. Bracket without pre-drilled holes used on T-H Marine Manual and Pro Hi Jacker 6, 8, 10 and 12″ jack plates

$49.95

Select options
In Stock

LB-3-RW Blank L. Bracket – STARBOARD side

L. Bracket without pre-drilled holes used on T-H Marine Manual and Pro Hi Jacker 6, 8, 10 and 12″ jack plates

$49.95

Select options
In Stock

LB-AT-4.6.8.10.12 to attach a Transducer Shield to ATLAS 8″ to 12″ jack plates

L Adaptor Bracket used to install a Transducer Shield to the side of an Atlas 8″, 10″ & 12″ Hydraulic Jack Plates

$49.95

Select options
In Stock

LB-SS-4-L to attach a Transducer Shield to Sea Star 4″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 4″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-SS-4-R to attach a Transducer Shield to Sea Star 4″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 4″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-SS-6-8-10-12-L to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 6″, 8″, 10″ or 12″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-SS-6-8-10-12-R to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate

L Adaptor Bracket used to install a Transducer Shield to the side of an Sea Star 6″, 8″, 10″ or 12″ Hydraulic Jack Plate

$59.95

Select options
In Stock

LB-CMC-5/5-8 to fit 5.5 to 8″ CMC Jack Plate

L Bracket to attach a Transducer Shield to the side of a CMC jack plate.

It is very important that you complete the questionnaire when ordering this item.
The information you provide will help us to assist you better and avoid a delay in shipping your order.

$64.95

Select options
In Stock

LB-DETW-6.8.10 – L Bracket to attach a Transducer Shield to a Detwiler Jack Plate

L Bracket used to attach a Transducer Shield to the side of Detwiler 6″, 8″ or 10″ Jack Plate.

Please complete the questionnaire when placing your order. The more information that we have about your boat and jack plate, the better we can assist you. Contact us if you need further assistance.

$64.95

Select options
In Stock

LB-SM-10/12-RW for Slidemaster 10″ or 12″ Jack Plate

L Adaptor Bracket to attach a Transducer Shield on the side of a 10″ & 12″ Slide Master Jack Plate. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item.

$49.95

Select options
In Stock

LB-SM-6/8 for Slidemaster 6″ or 8″ Jack Plate

L. Adapter Bracket to fit Slide Master 6″ and 8″ manual Jack Plate. Used to attach a Transducer Shield to the side of the jack plate.

It is VERY IMPORTANT that you complete the questionnaire in full when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

$49.95

Select options
On backorder

MK-Filler Block used to attach a Transducer Shield to a MinnKota Ultrex 36 volt with a Built in Down Image Transducer

Item # MK-UL-36-DI-Filler this item is used to attach a Transducer Shield to a 24v or 36v Minnkota “Ultrex” trolling motor with a built in Down Image transducer.

For 36 volt includes two 4.0” and one 6″ heavy duty stainless steel black powder coated straps.

This item must be attached to a Transducer Shield (sold separately) in order for this item to work on the trolling motor. After ordering the Filler, please Click on Shields to choose the correct Transducer Shield to suit your transducer.

Proudly Designed and Built in USA

See More Fish ………. Catch More Fish

$71.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

TM-AM-TM150-T to fit Airmar Transom transducer on Trolling Motor

Transducer Shield # TM-AM-TM150T to fit Airmar transom style transducer TM150-T onto a Trolling Motor. Please complete the questionnaire when ordering this item.

If your Airmar transducer can be taken apart to remove the pod from inside the casing, then this is not the Transducer Shield for you.

$149.00

Select options
In Stock

TS-HDI-3 fits Lowrance HDI xDucer (50/200kHz) 000-10977-001 for Trolling Motor or Jack Plate install

Fits Lowrance® Elite HDI (Hybrid Dual Imaging) Skimmer transducer # 000-10977-001 (50/200kHz)

$89.95

Select options
In Stock

TS-HDI-4 fits Lowrance HDI (83/200kHz) Transducer # 000-10976-001, # 000-12728-001 & # 000-12570-001

Fits Lowrance® HDI (Hybrid Dual Imaging) 83/200kHz Skimmer transducer # 000-10976-001. # 000-12728-001 & # 000-12570-001. It can be attached to a trolling motor, to the side of a Jack Plate with an L Bracket, or on a hole shot plate (under the jack plate) with a Wedge

$89.95

Select options
In Stock

TS-LSS-3D fits Lowrance LSS1 Structure Scan & Pod xDucers together usually on a Trolling Motor

Fits Lowrance® LSS1 (6″) Structure Scan Transducer with the Lowrance® Pod Transducer. It is very important that you complete the questionnaire when ordering this item.

$185.00

Select options
Out Of Stock

TS-LSS-3D-AM to fit Lowrance LSS1 and Airmar TM150 pod transducer

Fits Lowrance® LSS1 (6″) Structure Scan Transducer with an Airmar® (TM150M) Pod Transducer. It is very important that you complete the questionnaire when ordering this item.

$185.00

Select options
In Stock

TS-LSS2-2L fits Lowrance LSS2 Structure Scan Transducer on a Set Back or Hole Shot Plate

Fits Lowrance LSS2 structure scan 10-1/4″ transducer for installation on SetBack/Step OR Hole Shot/Baffle plates.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
It is very important that you complete the questionnaire when ordering this item.

$99.95

Select options

CLOSE

My Account
Search

Search for:
0