• AP-CSi to fit a Humminbird Side Image xDucer XNT 9 SI 180 T or XNT 9 HW MSI 150 T on a Transom
    AP-CSi Armor Plate
    In Stock

    AP-CSi to fit a Humminbird Side Image xDucer XNT 9 SI 180 T or XNT 9 HW MSI 150 T on a Transom

    For transom installation to protect your transducer from side to side and front to back impact.  Ideal for boats with flat transoms and without a jack plate.  Recommended as an added accessory to our SBB-5 Spring Back Bracket.

    $49.95
    Select options
  • Transducer Shield # TG-GT-6
    TG-GT-6 shown with Garmin Transducer (not included)
    In Stock

    TG-GT-6 to fit Garmin GT22, GT24, GT52 or GT54

    Choose this item to attach a Garmin® Transducers GT 22, GT 24, GT52 or GT54 on a Trolling Motor, Jack Plate or Transom Set Back.  This Transducer Shield will not fit the new Garmin GT 36 or GT56 transducer.

    NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

    It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item.

    $109.95
    Select options
  • TM-H8.3 fits Humminbird Mega MSI Transducer
    Transducer Shield TM-H8.3 components
    In Stock

    TM-H8.3 fits Humminbird® Solix or Helix Mega G2N, G3N or G4N Mega MSI T Transducer

    TM-H-8.3 fits Humminbird® Solix Mega Si GPS G2N, G3N transducer XM 14 HW MSI T or Helix Mega Si GPS G3N or G4N transducer XM 9 HW MSI T,  XTM 9 HW MSI T or XM 14 HW MSI T.   If this item is going on a Trolling Motor, please answer the trolling motor questions.  If this item is going on the Jack Plate please answer all the questions about your jack plate and boat.

    NOTE:  A transducer attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, will not track the bottom when the boat is up on plane.  An in hull transducer will be required or recommended to track the bottom when the boat is up on plane.

    $179.00
    Select options
  • TM-H7.1 fits Humminbird® Solix Mega G2N or G3N DiTransducer XM 14 HW MDI T or Helix Mega G3N or G4N Di Transducer XM 9 HW MDI T
    TM-H7.1 picture shows Transducer Shield Rail and Block
    In Stock

    TM-H7.1 fits Humminbird® Solix Mega G2N or G3N DiTransducer XM 14 HW MDI T or Helix Mega G3N or G4N Di Transducer XM 9 HW MDI T

    TM-H-7.1 fits Humminbird® SOLIX Mega Di GPS G2N transducer XM 14 HW MDI T or XTM 14 HW MDI T or Helix Mega Di GPS G3N transducer XM 9 HW MDI T or XTM 9 HW MDI T for trolling motor, set back, hole shot plate or jack plate installation.  If this item is going on a Trolling Motor, please answer the trolling motor questions.  If this item is going on the Jack Plate please answer all the questions about your jack plate and boat.  It is very important that you answer the questionnaire in full please.

    NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

    $179.00
    Select options
  • RAM BT-2 for Humminbird XTM trolling motor transducers
    Ram BT and Strap showing transducer
    In Stock

    RAM BT-2 for Humminbird XTM trolling motor transducers

    Ram and Strap to fit a Humminbird® trolling motor XTM style transducer.  Enlarge photos to identify your transducer.  Please complete the questionnaire when ordering this item.

    $34.95
    Select options
  • TM-CSI-2 fits Humminbird Side Image XNT 9 SI 180 T, XNT 9 HW MSI 150 T or XNT 9 QB 90 T xDucer for Trolling Motor, Jack Plate or Set Back
    Transducer Shield TM-CSI-2 and Humminbird compact side image transducer (not included)
    In Stock

    TM-CSI-2 fits Humminbird Side Image XNT 9 SI 180 T, XNT 9 HW MSI 150 T or XNT 9 QB 90 T xDucer for Trolling Motor, Jack Plate or Set Back

    Fits Humminbird® Compact Side Image XNT 9 SI 180T, XNT 9 HW MSI 150 T or Quad Beam XNT 9 QB 90 T transducer

    NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

    $74.95
    Select options
  • TG-TUG to fit Garmin traditional dual beam / dual frequency transducer # 010-10272-00 or 010-10249-20
    Transducer Shield to fit Garmin dual beam 4 pin transducer
    Out Of Stock

    TG-TUG to fit Garmin traditional dual beam / dual frequency transducer # 010-10272-00 or 010-10249-20

    TG-TUG is Ideal for Installing on a trolling motor.  It can also be attached on the side of a jack plate or on the boat set back with additional components.

    $139.00
    Select options
  • TM-DI-2 fits the Humminbird redesigned Down Image Transducer
    Picture shows Humminbird redesigned Down Image transducer (not included) and TM-DI-2 Transducer Shield
    In Stock

    TM-DI-2 fits Humminbird Down Image Xducer # XNT 9 DI T (RD), XM 9 MDI T, Mega XNT 9 HW MDI 75 T or Onix Xducer # XNT 14 DI T (RD) for Trolling Motor, Jack Plate or Set Back

    TM-DI-2 fits Humminbird® Down Image Transducer # XNT 9 DI T (RD),  XNT 14 DI T (RD) and XNT 9 HW MDI 75 T for trolling motor, set back or jack plate installation.  It DOES NOT fit the ORIGINAL Down Image transducer # # XNT 9 DI T.

    NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

    $79.95
    Select options
  • TM-HDsi fits Humminbird® HDSI xDucer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T
    TM-HDsi
    In Stock

    TM-HDsi fits Humminbird® HDSI xDucer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T

    TM-HDSi fits Humminbird® High Definition Side Image Transducer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T for trolling motor, set back or jack plate installation. 

    NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

     

    $79.95
    Select options
  • TM-XTM-75/150 T to fit Humminbird XTM 9 HW MDI 75 T or XTM 9 HW MSI 150 T transducer
    In Stock

    TM-XTM-75/150 T to fit Humminbird XTM 9 HW MDI 75 T or XTM 9 HW MSI 150 T transducer

    TM-XTM-75/150 T fits Humminbird® Helix Mega Di transducer XTM 9 HW MDI 75 T or Helix Mega Si transducer XM 9 HW MSI 150 T. for trolling motor, set back, hole shot plate or jack plate installation.
    If this item is going on a Trolling Motor, please answer the trolling motor questions.  If this item is going on the Jack Plate please answer all the questions about your jack plate and boat.  It is very important that you answer the questionnaire in full please.
    NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

    $99.95
    Select options
  • TM-HX-3 fits Humminbird® Helix G2N Mega Si or Solix G1N Si Transducer
    In Stock

    TM-HX-3 fits Humminbird® Helix G2N Mega Si or Solix G1N Si Transducer

    TM-HX-3 fits Humminbird® Chirp Helix Mega Si GPS G2N transducer XM 9 20 MSI T or Solix G2N  Si XM transducer XM 14 20 MSI T for trolling motor, set back or jack plate installation.  If this item is going on a Trolling Motor, please answer the trolling motor questions.  If this item is going on the Jack Plate please answer all the questions about your jack plate and boat.  It is very important that you answer the questionnaire in full please.

    NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

    $179.00
    Select options