Shop Category – Transducer Shield and Saver

Showing 97–108 of 148 results

In Stock

TG-DS-8.4 fits Garmin GT40

^{TG-DS-8.4 Transducer Shield is ideal for Installing on a trolling motor, on the side of a jack plate or on the boat set back. Additional components will be required. NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane. For bottom reading on plane, a transducer inside the hull will be required. It is very important that you complete the questionnaire when ordering this item.}

$139.95

Select options
In Stock

AP-DS-Vu to fit Garmin GT30 and GT34

For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket. Please complete the questionnaire below when ordering this product.

$69.95

Select options
In Stock

AP-D-Vu to fit Garmin GT20

For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket. Please complete the questionnaire below when ordering this product.

$69.95

Select options
In Stock

TG-DS-Vu to fit Garmin GT30 and GT34

This item is user friendly for various installation options – * Trolling Motor * Side of the Jack Plate * Hole Shot Plate or * Set Back Additional components are required.
When ordering this item, please note in the comment area which transducer you have. Either the Garmin GT30 or GT34 transducer. It is important for us to know this please. This Transducer Shield DOES NOT fit the Garmin GT 36 or GT 56 transducer.

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

$89.95

Select options
In Stock

TG-D-Vü fits Garmin GT20

To fit Garmin HD ID Down Vu (8 pin) transducer number 010-12087-001 (GT20-TM)

$89.95

Select options
In Stock

TM-DI-2 fits Humminbird Down Image Xducer # XNT 9 DI T (RD), XM 9 MDI T, Mega XNT 9 HW MDI 75 T or Onix Xducer # XNT 14 DI T (RD) for Trolling Motor, Jack Plate or Set Back

TM-DI-2 fits Humminbird® Down Image Transducer # XNT 9 DI T (RD), XNT 14 DI T (RD) and XNT 9 HW MDI 75 T for trolling motor, set back or jack plate installation. It DOES NOT fit the ORIGINAL Down Image transducer # # XNT 9 DI T.

^NOTE^{: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.}

$79.95

Select options
In Stock

TM-ONIX-2 fits Humminbird Side Image Xducer XT 14 20 HDSI T (RD) and XT 14 74 HDSI T (RD)

TM-ONIX-2 fits Humminbird® HD Side Image Transducer # XT 14 20 HDSI T (RD) or XT 14 74 HDSI T (RD) for trolling motor, set back or jack plate installation. It DOES NOT fit the ORIGINAL transducer # XT 14 20 HDSI T or XT 14 74 HDSI T. ONIX transducer differences

$84.95

Select options
In Stock

LB-CMC-5/5-8 to fit 5.5 to 8″ CMC Jack Plate

L Bracket to attach a Transducer Shield to the side of a CMC jack plate.

It is very important that you complete the questionnaire when ordering this item.
The information you provide will help us to assist you better and avoid a delay in shipping your order.

$64.95

Select options
In Stock

EXT-3.0 Extension

Aluminum extension attached between an L Bracket and Transducer Shield will lower the transducer if turning chines or trim tabs interfere with transducer side signal

$40.00

Add to cart
In Stock

ATLAS 8″ to 14″ Jack Plate : L Bracket # LB-AT-4.6.8.10.12 (without offset)

L Bracket to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ and 12″ Jack Plate. PLEASE make sure that your jack plate size and Transducer Shield is listed in the description to the left. The larger transducers require our L Bracket with an “offset” or “spacer” to keep the trim rod from hitting the transducer.

It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

$49.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

TM-ONIX-1 fits Humminbird Side Image Xducer XT 14 20 HDSI T or XT 14 74 HDSI T

TM-ONIX-1 fits Humminbird® HD Side Image Transducer # XT 14 20 HDSI T or XT 14 74 HDSI T for trolling motor, set back or jack plate installation. It DOES NOT fit the REDESIGNED transducer # XT 14 20 HDSI T (RD). ONIX transducer differences

$79.95

Select options
In Stock

TS-HDI-3 fits Lowrance HDI xDucer (50/200kHz) 000-10977-001 for Trolling Motor or Jack Plate install

Fits Lowrance® Elite HDI (Hybrid Dual Imaging) Skimmer transducer # 000-10977-001 (50/200kHz)

$89.95

Select options

My Account
Search

Search for:
0