Shop - Transducer Shield and Saver - Page 4

Showing 91–120 of 152 results

In Stock

LB-CMC-5/5-8 to fit 5.5 to 8″ CMC Jack Plate

L Bracket to attach a Transducer Shield to the side of a CMC jack plate.

It is very important that you complete the questionnaire when ordering this item.
The information you provide will help us to assist you better and avoid a delay in shipping your order.

$64.95

Select options
On backorder

LB-DETW-6.8.10 – L Bracket to attach a Transducer Shield to a Detwiler Jack Plate

L Bracket used to attach a Transducer Shield to the side of Detwiler 6″, 8″ or 10″ Jack Plate.

Please complete the questionnaire when placing your order. The more information that we have about your boat and jack plate, the better we can assist you. Contact us if you need further assistance.

$64.95

Select options
In Stock

LB-SM-10/12 for Slidemaster 10″ or 12″ Jack Plate

L Adaptor Bracket to attach a Transducer Shield on the side of a 10″ & 12″ Slide Master Jack Plate. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item.

$49.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

LB-SM-6/8 for Slidemaster 6″ or 8″ Jack Plate

L. Adapter Bracket to fit Slide Master 6″ and 8″ manual Jack Plate. Used to attach a Transducer Shield to the side of the jack plate.

It is VERY IMPORTANT that you complete the questionnaire in full when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

$49.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

LWG-2 Wedge for Hole Shot or Set Back install

LWG-2 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Jack Plate hole shot plate.

$19.95

Select options
In Stock

LWG-3 Wedge for Hole Shot or Set Back install

LWG-3 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Hole Shot Plate under a Jack Plate.

$24.95

Select options
In Stock

MG-360-SLEEVE to attach Humminbird 360 to Motorguide outer shaft

MG-360-Sleeve Aluminum Sleeve used to fit a Humminbird 360 Imaging to a Motorguide Trolling Motor Outer Shaft. IMPORTANT NOTE: Some of the NEWER Motorguide trolling motors have the same size shaft as Minnkota and will not need the MG-360-SLEEVE when attaching a Humminbird 360.

$98.95

Add to cart
In Stock

MG-GS-P1 Grass Shredder Plate to fit Motorguide® trolling motors

Cut through the grass and weeds when fishing in grassy areas. Stainless Steel and Black Powder Coated. Pictures are shown unpainted for easy viewing.

Customer Comment: I want to let you know how much I love my newly purchased Grass Shredder for my MinnKota Fortrex. I installed it as per the instructions and headed out to the Potomac River for a two day club tourney. The Shredder was awesome in all that grass and helped save my batteries. I did not once have to stop and clean the grass off of my trolling motor. To top it all off, I won the event with 10 bass for 23.88 lbs. and caught the biggest Snakehead of my fishing career. The buff was a pleasant surprise and greatly appreciated as I have had 12 skin cancers removed from my head and neck over the years…Thank you, thank you!

$34.95

Add to cart
In Stock

Mini Receiver Ring Garmin Force Trolling Motor

^{The Receiver Ring System is designed to allow the attachment of up to three Transducer Shield & Saver product accessories to your trolling motor. We offer a Full or Mini Receiver Ring to fit Garmin Force, Lowrance Ghost or Minnkota Ultrex trolling motors. Coming soon for Motorguide.}

^{The Receiver Ring securely bolts under the trolling motor head for easy accessory attachments.}

^{Check out the additional T S & S product accessories available to attach to our Receiver Ring system:}

^{* ACC-RR-360 is designed for the Humminbird 360}

^{* ACC-TL is designed for the Humminbird TargetLock}

^{* Fish Sniff Fiber Pole is designed for any of the “forward facing transducers”}

^{* Offering three different size Accessory Plates to attach to the Receiver Ring System: ACC-5.1 or ACC-3.5 or ACC-2.5}

^{The Receiver Rings and Accessories are built in 6061 x 3/4″ thick aircraft aluminum alloy, black powder coated and include stainless steel bolts, washers and lock nuts}

Proudly Designed and Built in Alabama USA

See More Fish ………. Catch More Fish

$169.00

Add to cart
On backorder

Mini Receiver Ring Lowrance Ghost Trolling Motor

^{The Receiver Ring System is designed to allow the attachment of up to three Transducer Shield & Saver product accessories to your trolling motor. We offer a Full or Mini Receiver Ring to fit Garmin Force, Lowrance Ghost or Minnkota Ultrex trolling motors. Coming soon for Motorguide.}

^{The Receiver Ring securely bolts under the trolling motor head for easy accessory attachments.}

^{Check out the additional T S & S product accessories available to attach to our Receiver Ring system:}

^{* ACC-RR-360 is designed for the Humminbird 360}

^{* ACC-TL is designed for the Humminbird TargetLock}

^{* Fish Sniff Fiber Pole is designed for any of the “forward facing transducers”}

^{* Offering three different size Accessory Plates to attach to the Receiver Ring System: ACC-5.1 or ACC-3.5 or ACC-2.5}

^{The Receiver Rings and Accessories are built in 6061 x 3/4″ thick aircraft aluminum alloy, black powder coated and include stainless steel bolts, washers and lock nuts}

Proudly Designed and Built in Alabama USA

See More Fish ………. Catch More Fish

$169.00

Add to cart
In Stock

Mini Receiver Ring Minnkota Ultrex Trolling Motor

^{The Receiver Ring System is designed to allow the attachment of up to three Transducer Shield & Saver product accessories to your trolling motor. We offer a Full or Mini Receiver Ring to fit Garmin Force, Lowrance Ghost or Minnkota Ultrex trolling motors. Coming soon for Motorguide.}

^{The Receiver Ring securely bolts under the trolling motor head for easy accessory attachments.}

^{Check out the additional T S & S product accessories available to attach to our Receiver Ring system:}

^{* ACC-RR-360 is designed for the Humminbird 360}

^{* ACC-TL is designed for the Humminbird TargetLock}

^{* Fish Sniff Fiber Pole is designed for any of the “forward facing transducers”}

^{* Offering three different size Accessory Plates to attach to the Receiver Ring System: ACC-5.1 or ACC-3.5 or ACC-2.5}

^{The Receiver Rings and Accessories are built in 6061 x 3/4″ thick aircraft aluminum alloy, black powder coated and include stainless steel bolts, washers and lock nuts}

Proudly Designed and Built in Alabama USA

See More Fish ………. Catch More Fish

$169.00

Add to cart
In Stock

MK-Filler Block used to attach a Transducer Shield to a MinnKota Ultrex 36 volt

Item # MK-UL-36-DI-Filler this item is used to attach a Transducer Shield to a 24v or 36v Minnkota “Ultrex” trolling motor with a built in Down Image transducer.

For 36 volt includes two 4.0” and one 6″ heavy duty stainless steel black powder coated straps.

This item must be attached to a Transducer Shield (sold separately) in order for this item to work on the trolling motor. After ordering the Filler, please Click on Shields to choose the correct Transducer Shield to suit your transducer.

Proudly Designed and Built in US

$71.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

MK-GS-P1 Grass Shredder Plate to fit Minnkota 24v 74lb up to 36v 101lb trolling motors

Cut through the grass and weeds when fishing in grassy areas. Stainless Steel and Black Powder Coated. Pictures are shown unpainted for easy viewing.

Customer Comment: I want to let you know how much I love my newly purchased Grass Shredder for my MinnKota Fortrex. I installed it as per the instructions and headed out to the Potomac River for a two day club tourney. The Shredder was awesome in all that grass and helped save my batteries. I did not once have to stop and clean the grass off of my trolling motor. To top it all off, I won the event with 10 bass for 23.88 lbs. and caught the biggest Snakehead of my fishing career. The buff was a pleasant surprise and greatly appreciated as I have had 12 skin cancers removed from my head and neck over the years…Thank you, thank you!

$34.95

Add to cart
In Stock

MK-GS-P2 Grass Shredder Plate to fit Minnkota 36v 112lb Trolling Motor

Cut through the grass and weeds when fishing in grassy areas. Stainless Steel and Black Powder Coated. Pictures are shown unpainted for easy viewing.

Customer Comment: I want to let you know how much I love my newly purchased Grass Shredder for my MinnKota Fortrex. I installed it as per the instructions and headed out to the Potomac River for a two day club tourney. The Shredder was awesome in all that grass and helped save my batteries. I did not once have to stop and clean the grass off of my trolling motor. To top it all off, I won the event with 10 bass for 23.88 lbs. and caught the biggest Snakehead of my fishing career. The buff was a pleasant surprise and greatly appreciated as I have had 12 skin cancers removed from my head and neck over the years…Thank you, thank you!

$34.95

Add to cart
In Stock

Quest Trolling Motor Adaptor Plate

_{Item # Q-A-Plate – Quest Adaptor Plate is built in 6061 High Quality Aluminum Alloy and Black Powder Coated.}

_{About our Adaptor Plate: the Adaptor Plate can be attached to a Transducer Shield which will allow you to attach the Transducer Shield to a Minnkota Quest Trolling Motor so that the clamps / straps are attached to the housing correctly.}

_{About the Minnkota Quest Trolling Motor: the Minnkota Quest housing is configured differently to previous Minnkota models: 1. the skeg is off set; 2. the shaft is larger on the housing; and 3. the US2 sonar is shaped differently to the previous Ultrex trolling motor.}
_{The Good News is – if you already own one of our Transducer Shields simply purchase the Quest Adaptor Plate which will easily attach it to your previously purchased Transducer Shield (TM-H8.3, TG-HG-8.5, TS-AIHD-TS or TS-DSS3-TS).}
_{On the longer TS-DSS3-TS and TS-AIHD-TS Transducer Shields, it will be necessary to purchase an additional component “Ram” to close the gap between the US2 cone and the Transducer Shield. When placing your order, please select the Adaptor Plate with a Ram.}
_{The Quest Adaptor Plate cannot be used with a transducer only; it must be attached to a Transducer Shield.}

Another Cool Product Proudly Designed in USA

Price range: $40.00 through $81.85

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

Quick Clip

Stainless steel propeller safety clip. Never have to replace that rusted, broken or lost cotter pin again.

$3.95

Add to cart
In Stock

RAM BT-2 for Humminbird XTM trolling motor transducers

Ram and Strap to fit a Humminbird® trolling motor XTM style transducer. Enlarge photos to identify your transducer. Please complete the questionnaire when ordering this item.

$34.95

Select options
In Stock

Rite Hite L Bracket LB-RH-6

Rite Hite L Bracket without an Extender Plate is used when both pieces of the jack plate are at the same at the bottom of the jack plate.
Rite Hite L Bracket with an Extender Plate is used when the engine side piece of the jack plate is lower than the transom piece at the bottom.
Enlarge the jack plate pictures to determine which set up you will need.

Not sure what you need….. call 334-514-7147 or email a good side view photo of your jack plate showing the level of the bottom of the jack plate to: [email protected]

Price range: $54.95 through $103.95

Select options This product has multiple variants. The options may be chosen on the product page
In Stock

SSC-3 fits Humminbird XNT 9 20 T or XNT 14 20 T xDucer on a Trolling Motor

_{To attach and protect your Humminbird® XNT 9 20 T or XNT 14 20 T (transom style) transducer on a Trolling Motor. (This Transducer Shield will not fit Humminbird Side Image Transducer # XNT 9 SI 180 T. Please see Transducer Shield # TM-CSI)}

_{Please complete the information below when ordering this item.}

$29.95

Select options
In Stock

SSC-4 fits Humminbird XP 9 20 (T), XTM 9 20 T or XTM 14 20 T xDucers on a Trolling Motor

Fits Humminbird® Puck Transducer
XP 9 20 (T), XTM 9 20 T or XTM 14 20 T. This shield does not fit any of Humminbird’s side image transducers.

$29.95

Select options
In Stock

TM-CSI-2 fits Humminbird Side Image XNT 9 SI 180 T, XNT 9 HW MSI 150 T or XNT 9 QB 90 T xDucer for Trolling Motor, Jack Plate or Set Back

Fits Humminbird® Compact Side Image XNT 9 SI 180T, XNT 9 HW MSI 150 T or Quad Beam XNT 9 QB 90 T transducer

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

$74.95

Select options
In Stock

TG-D-Vü fits Garmin GT20

To fit Garmin HD ID Down Vu (8 pin) transducer number 010-12087-001 (GT20-TM)

$89.95

Select options
In Stock

TG-DS-9 fits Garmin GT21, GT23, GT41, GT50 and GT51

Ideal for Installing on a trolling motor, on the side of a jack plate or on the boat set back. Additional components will be required. This Transducer Shield will not fit the new Garmin GT 36 or GT 56 transducer.

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

It is very important that you complete the questionnaire when ordering this item.

$149.95

Select options
In Stock

TG-DS-Vu to fit Garmin GT30

This item is user friendly for various installation options – * Trolling Motor * Side of the Jack Plate * Hole Shot Plate or * Set Back Additional components are required.
This Transducer Shield DOES NOT fit the Garmin GT 36 or GT 56 transducer.

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

$99.95

Select options
In Stock

TG-DS-Vu-2 to fit Garmin GT34

This item is user friendly for various installation options – * Trolling Motor * Side of the Jack Plate * Hole Shot Plate or * Set Back Additional components are required.
It is important for us to know this please. This Transducer Shield DOES NOT fit the Garmin GT 36 or GT 56 transducer.

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

$99.95

Select options
Out Of Stock

TG-TUG to fit Garmin traditional dual beam / dual frequency transducer # 010-10272-00 or 010-10249-20

TG-TUG is Ideal for Installing on a trolling motor. It can also be attached on the side of a jack plate or on the boat set back with additional components.

$139.00

Select options
In Stock

TG-GT30-3D Transducer Shield to fit Garmin DownVü/SideVü GT30 and Pod GT8HW transducers together

Available Now. Transducer Shield to fit Garmin® DownVü/SideVü GT30-TM Transducer and GT8HW-IH pod transducer in tandem on trolling motors.

$224.95

Select options
In Stock

TM-AM-TM150-T to fit Airmar Transom transducer on Trolling Motor

Transducer Shield # TM-AM-TM150T to fit Airmar transom style transducer TM150-T onto a Trolling Motor. Please complete the questionnaire when ordering this item.

If your Airmar transducer can be taken apart to remove the pod from inside the casing, then this is not the Transducer Shield for you.

$149.00

Select options
In Stock

TM-DI fits Humminbird Down Image XNT 9 DI T xDucer for Trolling Motor, Jack Plate or Set Back

TM-DI fits Humminbird® Down Image Transducer # XNT 9 DI T for trolling motor, set back or jack plate installation. It DOES NOT fit the redesigned Down Image transducer # # XNT 9 DI T (RD). Onix Down Image Transducer XNT 14 DI T (RD) or XM 9 MDI T.

NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.

$74.95

Select options
In Stock

TM-DI-2 fits Humminbird Down Image Xducer # XNT 9 DI T (RD), XM 9 MDI T, Mega XNT 9 HW MDI 75 T or Onix Xducer # XNT 14 DI T (RD) for Trolling Motor, Jack Plate or Set Back

TM-DI-2 fits Humminbird® Down Image Transducer # XNT 9 DI T (RD), XNT 14 DI T (RD) and XNT 9 HW MDI 75 T for trolling motor, set back or jack plate installation. It DOES NOT fit the ORIGINAL Down Image transducer # # XNT 9 DI T.

^NOTE^{: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.}

$79.95

Select options

CLOSE

My Account
Search

Search for:
0