Showing 73–84 of 152 results
-
TS-TRI-SH combo to fit Lowrance Hook 2 / Reveal Triple Shot xDucer 000-14029-001 on Trolling Motor
$215.95Choose this item to attach a Lowrance® Hook2 / Reveal Triple Shot Transducer # 000-14029-001 on a Trolling Motor. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item. This Transducer Shield will NOT fit the latest Lowrance Triple Shot Transducer # 000-16285-001
-
TS-TRI-SH to fit Lowrance Hook 2 / Reveal Triple Shot Transducer # 000-14029-001 on Jack Plate, Hole Shot Plate or Set Back
$189.00Choose this item to attach a Lowrance® Hook2 / Reveal Triple Shot Transducer # 000-14029-001 for Jack Plate, Hole Shot Plate or Transom Set Back. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item. This Transducer Shield will NOT fit the latest Lowrance Triple Shot transducer # 000-16285-001
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required. -
TG-GT30-3D Transducer Shield to fit Garmin DownVü/SideVü GT30 and Pod GT8HW transducers together
$224.95Available Now. Transducer Shield to fit Garmin® DownVü/SideVü GT30-TM Transducer and GT8HW-IH pod transducer in tandem on trolling motors.
-
WG-3.5 Wedge used to attach TM-HX-1 Transducer Shield to a 90 degree Hole Shot Plate
$48.95WG-2.5 Wedge to attach Transducer Shield to 90 degree hole shot plate.
Used along with a Transducer Shield on 90 Degree Jack Plate with Hole Shot Plate. This wedge is suitable for our Humminbird® Transducer Shield # TM-HX-1
-
-
AP-HX-1 to fit Humminbird Mega SI or Solix SI Transducer on a Transom
$89.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket.
-
Cable Guiding Tower great for iPilot and xi5 series trolling motors
$98.95Item # MK-Cable Guiding Tower. This kit is ideal for trolling motors with “External Wiring” for example Minnkota Ulterra, Terrova, Power Drive and Motorguide xi5 series.
-
TS-HDI-4 fits Lowrance HDI (83/200kHz) Transducer # 000-10976-001, # 000-12728-001 & # 000-12570-001
$89.95Fits Lowrance® HDI (Hybrid Dual Imaging) 83/200kHz Skimmer transducer # 000-10976-001. # 000-12728-001 & # 000-12570-001. It can be attached to a trolling motor, to the side of a Jack Plate with an L Bracket, or on a hole shot plate (under the jack plate) with a Wedge
-
LWG-3 Wedge for Hole Shot or Set Back install
$24.95LWG-3 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Hole Shot Plate under a Jack Plate.
-
TM-HX-3 fits Humminbird® Helix G2N Mega Si or Solix G1N Si Transducer
$179.00TM-HX-3 fits Humminbird® Chirp Helix Mega Si GPS G2N transducer XM 9 20 MSI T or Solix G2N Si XM transducer XM 14 20 MSI T for trolling motor, set back or jack plate installation. If this item is going on a Trolling Motor, please answer the trolling motor questions. If this item is going on the Jack Plate please answer all the questions about your jack plate and boat. It is very important that you answer the questionnaire in full please.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
RAM BT-2 for Humminbird XTM trolling motor transducers
$34.95Ram and Strap to fit a Humminbird® trolling motor XTM style transducer. Enlarge photos to identify your transducer. Please complete the questionnaire when ordering this item.
-
MG-GS-P1 Grass Shredder Plate to fit Motorguide® trolling motors
$34.95Cut through the grass and weeds when fishing in grassy areas. Stainless Steel and Black Powder Coated. Pictures are shown unpainted for easy viewing.
Customer Comment: I want to let you know how much I love my newly purchased Grass Shredder for my MinnKota Fortrex. I installed it as per the instructions and headed out to the Potomac River for a two day club tourney. The Shredder was awesome in all that grass and helped save my batteries. I did not once have to stop and clean the grass off of my trolling motor. To top it all off, I won the event with 10 bass for 23.88 lbs. and caught the biggest Snakehead of my fishing career. The buff was a pleasant surprise and greatly appreciated as I have had 12 skin cancers removed from my head and neck over the years…Thank you, thank you!
