Showing 61–72 of 152 results
-
ATLAS 8″ to 12″ Jack Plate – R3 (w/ offset) – for STARBOARD or DRIVER side
$79.95L Bracket with 3 inch offset to attach a Transducer Shield to the side of an Atlas Hydraulic 8″, 10″ or 12″ Jack Plate. Also available for the Port Side. It is very important that you complete the questionnaire when ordering this item.you
-
AP-SP-SH Armor Plate to fit Lowrance® Hook 2 Split Shot Transducer & Eagle Splitshot HD
$79.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket.
It is very important that you complete the questionnaire in full when ordering any of our products. -
Rite Hite L Bracket LB-RH-6
Price range: $54.95 through $103.95Rite Hite L Bracket without an Extender Plate is used when both pieces of the jack plate are at the same at the bottom of the jack plate.
Rite Hite L Bracket with an Extender Plate is used when the engine side piece of the jack plate is lower than the transom piece at the bottom.
Enlarge the jack plate pictures to determine which set up you will need.Not sure what you need….. call 334-514-7147 or email a good side view photo of your jack plate showing the level of the bottom of the jack plate to: [email protected]
-
TM-AM-TM150-T to fit Airmar Transom transducer on Trolling Motor
$149.00Transducer Shield # TM-AM-TM150T to fit Airmar transom style transducer TM150-T onto a Trolling Motor. Please complete the questionnaire when ordering this item.
If your Airmar transducer can be taken apart to remove the pod from inside the casing, then this is not the Transducer Shield for you.
-
360 Stabilizer attaches to Humminbird 360 on a Minnkota Ultrex
$149.00Item # 360 Stabilizer to stabilize the Humminbird® 360 Imaging on a Minnkota® Ultrex trolling motor. It is built in 5/16 aluminum alloy and black powder coated. The total length is 15-1/2″ and attaches to the existing Humminbird® 360 Imaging bracket on a Minnkota® Ultrex Trolling Motor.
The purpose of our 360 Stabilizer is to: (1) reduce vibration of the Humminbird® 360 when the boat is up on plane and going through rough conditions (2) reduce the chance of breaking the Humminbird® 360 shaft when the transducer comes in contact with underwater obstruction (3) adds support to the Humminbird® 360 shaft and reduces flexing (4) reduces vibration to the 360 transducer when the trolling motor is deployed in the water and in trolling mode, and (5) enhances the structure definition on the fish finder.
Simple installation: attach our 360 Stabilizer base bracket to the existing holes in the Humminbird® 360 mounting bracket and clamp the end of the 360 Stabilizer to the Humminbird® 360 shaft.
-
Tool Buddy Premium TBP-BL without Cup Holder (tools shown are not included)
$49.95Tool Buddy Premium without Cup Holder (tools shown are not included)
Item # TBP-BL BLACK @ $49.95Description
* Back Plate 1/4” thick x 7-1/2″ Wide x 8-5/8” High with two mounting holes
* Shelf (tool holder) 7-1/8″ Long x 2-1/2” Depth
* Two ¼” holes for diamond files, Eight 1/8” holes for hanging lures and Six tool openings:
* One 2-1/8 x 5/16 for measuring board, One 2-1/8 x 11/16, Two 1-15/16 x 1/2,
* One 1-1/4 x ¾ and One 1-1/4 x ½ -
Tool Buddy Premium Deluxe TBPDX-BL with Stainless Cup Holder (tools shown are not included)
$64.95Tool Buddy Premium Deluxe with Stainless Cup Holder (tools shown are not included)
Item # TBPDX-BL BLACK @ $64.95
Description
* Back Plate 1/4” thick x 11-1/2” Wide x 8-5/8” High with up to six mounting holes
* Shelf (tool holder) 10-7/8” Long x 2-1/2” Wide and 3-5/8” Wide at cup holder
* Cup holder opening 2-11/16 diameter
* Three ¼” holes for diamond files, Eight 1/8” holes for hanging lures and Six tool openings:
* One 2-1/8 x 5/16 for measuring board, One 2-1/8 x 11/16, Two 1-15/16 x 1/2,
* One 1-1/4 x ¾ and One 1-1/4 x ½ -
Tool Buddy Sport TBS-BL without Cup Holder (tools shown are not included)
$39.95Tood Buddy Sport without cupholder (tools shown are not included)
Item # TBS-BL BLACK @ $39.95Description
* Back Plate 1/4” thick x 5-1/2″ Wide x 8-5/8” High with two mounting holes
* Shelf (tool holder) 5-1/4” Long x 2-1/2” Wide x 3/8 Thick
* One ¼” hole for diamond file, Six 1/8” holes for hanging lures & Four tool openings
* One 2-1/8 x 5/16 for measuring board, One 2-1/8 x 11/16, Two 1-15/16 x ½ -
Tool Buddy Sport Deluxe TBSDX-BL with Stainless Cup Holder (tools shown are not included)
$54.95Tood Buddy Sport Deluxe with Stainless Cup Holder (tools shown are not included)
Item # TBSDX-BL BLACK @ $54.95Description
* Back Plate 1/4” thick x 8-8-7/8″ Wide x 8-5/8” High with two mounting holes
* Shelf (tool holder) 8-5/8” Long x 2-1/2” Wide x 3/8 Thick and 3-5/8” Wide at cup holder
* Cup holder opening 2-11/16 diameter
* One ¼” hole for diamond file, Six 1/8” holes for hanging lures & Four tool openings
* One 2-1/8 x 5/16 for measuring board, One 2-1/8 x 11/16, Two 1-15/16 x ½ -
AP-TRI-SH to fit Lowrance® Hook2 / Reveal Triple Shot Transducer # 000-14029-001 on a Transom
$94.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket. This Armor Plate will NOT fit the latest Lowrance Triple Shot transducer # 000-16285-001
It is very important that you complete the questionnaire in full when ordering any of our products. -
Grass Off Deflector Rod to fit Minnkota & Motorguide 36v trolling motors
$49.95Eliminate and reduce the accumulation of vegetation on top of trolling motor. Suitable for Motorguide 36v and Minnkota 24v, 36v 101 and 112 trolling motors. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item.
-
TS-SP-SH to fit Lowrance® Hook2 Split Shot transducer 000-14028-001
$89.95Fits Lowrance® Hook² Split Shot transducer 000-14028-001 It can be attached to a trolling motor, to the side of a Jack Plate with an L Bracket, or on a hole shot plate (under the jack plate) with a Wedge. This Transducer Shield will NOT fit the latest Lowrance Split Shot transducer # 000-16284-001
