Showing 133–144 of 145 results
-
LB-DETW-6.8.10 – L Bracket to attach a Transducer Shield to a Detwiler Jack Plate
$64.95L Bracket used to attach a Transducer Shield to the side of Detwiler 6″, 8″ or 10″ Jack Plate.
Please complete the questionnaire when placing your order. The more information that we have about your boat and jack plate, the better we can assist you. Contact us if you need further assistance.
-
LWG-2 Wedge for Hole Shot or Set Back install
$19.95LWG-2 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Jack Plate hole shot plate.
-
TS-LSS-3D fits Lowrance LSS1 Structure Scan & Pod xDucers together usually on a Trolling Motor
$185.00Fits Lowrance® LSS1 (6″) Structure Scan Transducer with the Lowrance® Pod Transducer. It is very important that you complete the questionnaire when ordering this item.
-
LB-SM-10/12 for Slidemaster 10″ or 12″ Jack Plate
$49.95L Adaptor Bracket to attach a Transducer Shield on the side of a 10″ & 12″ Slide Master Jack Plate. It is VERY IMPORTANT that you complete the questionnaire below in full when ordering this item.
-
LB-BMA-6/8/10/12-R BOB’S Machine Jack Plate – STARBOARD SIDE – New adjustable angle!
$69.95LB-BMA-6.8.10.12-R Fits 6″, 8″, 10″ & 12″ Bob’s Hydraulic Jack Plates. Used to attach a Transducer Shield to the side of the jack plate.
It is very important that you complete the questionnaire when ordering this product. The information that you provide will help us to assist you better and avoid a delay in shipping your order. The more information that we have about your boat and jack plate, the better we can assist you.
Contact us if you need further assistance.
-
WG-1 Wedge to attach a Transducer Shield to a Set Back or Hole Shot Plate
$14.95WG-1 Wedge along with a Transducer Shield will put the Transducer at the correct angle when the boat is in the water when installed on a Boat Set Back or Jack Plate hole shot/baffle plate
-
TM-HDsi fits Humminbird® HDSI xDucer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T
$79.95TM-HDSi fits Humminbird® High Definition Side Image Transducer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T for trolling motor, set back or jack plate installation.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
TM-CSI-2 fits Humminbird Side Image XNT 9 SI 180 T, XNT 9 HW MSI 150 T or XNT 9 QB 90 T xDucer for Trolling Motor, Jack Plate or Set Back
$74.95Fits Humminbird® Compact Side Image XNT 9 SI 180T, XNT 9 HW MSI 150 T or Quad Beam XNT 9 QB 90 T transducer
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
Quick Clip
$3.95Stainless steel propeller safety clip. Never have to replace that rusted, broken or lost cotter pin again.
-
SSC-4 fits Humminbird XP 9 20 (T), XTM 9 20 T or XTM 14 20 T xDucers on a Trolling Motor
$29.95Fits Humminbird® Puck Transducer
XP 9 20 (T), XTM 9 20 T or XTM 14 20 T. This shield does not fit any of Humminbird’s side image transducers. -
SSC-3 fits Humminbird XNT 9 20 T or XNT 14 20 T xDucer on a Trolling Motor
$29.95To attach and protect your Humminbird® XNT 9 20 T or XNT 14 20 T (transom style) transducer on a Trolling Motor. (This Transducer Shield will not fit Humminbird Side Image Transducer # XNT 9 SI 180 T. Please see Transducer Shield # TM-CSI)
Please complete the information below when ordering this item.
-
SSC-2 fits Lowrance Pod PDT-WBL (106-74) transducer on a Trolling Motor
$29.95Fits Lowrance® Pod transducer PDT-WBL (106-74).
(With slight modifications, this Transducer Shield can be used for the Garmin® Pod transducer)
