Wedges and Trolling Motor Adaptors

Showing all 10 results

In Stock

LWG-2 Wedge for Hole Shot or Set Back install

LWG-2 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Jack Plate hole shot plate.

$19.95

Select options
In Stock

LWG-3 Wedge for Hole Shot or Set Back install

LWG-3 wedge along with a Transducer Shield will put the transducer at the correct angle when the boat is in the water, when installed on a boat set back/step or Hole Shot Plate under a Jack Plate.

$24.95

Select options
In Stock

Quest Trolling Motor Adaptor Plate

_{Item # Q-A-Plate – Quest Adaptor Plate is built in 6061 High Quality Aluminum Alloy and Black Powder Coated.}

_{About our Adaptor Plate: the Adaptor Plate can be attached to a Transducer Shield which will allow you to attach the Transducer Shield to a Minnkota Quest Trolling Motor so that the clamps / straps are attached to the housing correctly.}

_{About the Minnkota Quest Trolling Motor: the Minnkota Quest housing is configured differently to previous Minnkota models: 1. the skeg is off set ; 2. the shaft is larger on the housing; and 3. the US2 sonar is shaped differently to the previous Ultrex trolling motor.}
_{The Good News is – if you already own one of our Transducer Shields simply purchase the Quest Adaptor Plate which will easily attach it to your previously purchased Transducer Shield (TM-H8.3, TG-HG-8.5, TS-AIHD-TS or TS-DSS3-TS).}
_{On the longer TS-DSS3-TS and TS-AIHD-TS Transducer Shields, it will be necessary to purchase an additonal component “Ram” to close the gap between the US2 cone and the Transducer Shield. When placing your order, please select the Adaptor Plate with a Ram.}
_{The Quest Adaptor Plate cannot be used with a transducer only, it must be attached to a Transducer Shield.}

Another Cool Product Proudly Designed in USA

See More Fish ………. Catch More Fish

$40.00 – $81.85

Select options This product has multiple variants. The options may be chosen on the product page
On backorder

Ram Rail Kit for small Minnkota Trolling Motors

The Ram Rail Kit includes Skeg, 2 stainless steel straps & hardware. The kit can only be installed on a MinnKota trolling motor that has the Prop & Skeg on opposite ends and when the transducer to be attached is too long for the space between the propeller and skeg.

A transducer cannot be attached directly to the Ram Rail Kit and must be purchased along with a specific Transducer Shield to suit your transducer. After purchasing the Ram Rail Kit, click on “Shields” and choose the Transducer Shield to suit your transducer.

This product can be used with most Humminbird, Garmin & Lowrance Transducer Shields made by Transducer Shield and Saver.

Proudly designed and built in USA

$150.00

Select options
In Stock

TS-LSS2-2L fits Lowrance LSS2 Structure Scan Transducer on a Set Back or Hole Shot Plate

Fits Lowrance LSS2 structure scan 10-1/4″ transducer for installation on SetBack/Step OR Hole Shot/Baffle plates.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
It is very important that you complete the questionnaire when ordering this item.

$99.95

Select options
In Stock

TS-LSS2-L fits Lowrance LSS2 Structure Scan Transducer on a Jack Plate

_{Easily attaches a Lowrance® LSS2 structure scan transducer, with ADDITIONAL components to your Jack Plate or Boat Set Back.}

_{^NOTE^{: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.}}

_{It is VERY IMPORTANT that you complete the questionnaire when ordering this item.}

$169.00

Select options
In Stock

WG-1 Wedge to attach a Transducer Shield to a Set Back or Hole Shot Plate

WG-1 Wedge along with a Transducer Shield will put the Transducer at the correct angle when the boat is in the water when installed on a Boat Set Back or Jack Plate hole shot/baffle plate

$14.95

Select options
In Stock

WG-3.5 Wedge used to attach TM-HX-1 Transducer Shield to a 90 degree Hole Shot Plate

WG-2.5 Wedge to attach Transducer Shield to 90 degree hole shot plate.

Used along with a Transducer Shield on 90 Degree Jack Plate with Hole Shot Plate. This wedge is suitable for our Humminbird® Transducer Shield # TM-HX-1

$48.95

Select options
In Stock

WG-LSS2 to fit Humminbird TM-HX-3, TM-H8.3 or Garmin TG-HG-8.5 Transducer Shield on Set Back or Hole Shot Plate (10-12″ jack plates only)

Wedge used when attaching a Humminbird® TM-HX-3 or TM-H8.3 Transducer Shield on a boat Set-Back OR on a Hole Shot Plate under a jack plate. This Wedge CANNOT be used on a 90 ° degree Jack Plate.

$47.00

Select options
In Stock

WG-LSS2 to fit Lowrance LSS2, Total Scan, 3-on-1, 2-in-1, Structure Scan 3D Humminbird TM-HX-3 or TM-H8.3 on Set Back or Hole Shot Plate (10-12″ jack plates only)

^{This wedge is used when attaching a Lowrance 10-1/4″ transducer with a Transducer Shield to the Set Back of a Boat – example some Ranger Boats have a good set back.}

$47.00

Select options