Showing 37–48 of 161 results
-
360 Humminbird to a Motorguide Tour 2″ Outer Shaft # 360-S-CAB-MG
$285.00360-S-CAB-MG: Conversion Adapter Bracket will allow you to fit the original Humminbird 360 “S” Shape bracket to the 2″ outer shaft on a Motorguide Tour or Tour Pro trolling motor.
-
360 Humminbird – Fortrex Bracket to Ultrex # 360-S-CAB-ULT
$299.00360-S-CAB-ULT: Conversion Adapter Bracket will allow you to fit the original Humminbird 360 “S Shape bracket to a MinnkotaUltrex trolling motor.
-
Buzz Bar / Wire Terminals
$24.95 – $25.95Buzz Bar / Wire terminal to connect wires at the end of the dedicated line for depth finders.
-
“The Wedge” – Trolling Motor Shallow Water Bracket
$114.95 – $134.95Let’s Fish Shallow with “The Wedge”. No more holding the trolling motor rope to fish shallow.
Simply place “The Wedge” beneath the trolling motor bracket and GO SHALLOW.
Available to fit Garmin Force, Lowrance Ghost, Minnkota Ultrex and Fortrex or Motorguide Pro Tour. -
TG-HG-8.5 Transducer Shield to fit Garmin GT 56 or GT 36
$159.00TG-HG-8.5 Transducer Shield ideal for Installing on a trolling motor, on the side of a jack plate or on the boat set back. Additional components will be required.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane. For bottom reading on plane, a transducer inside the hull will be required.
-
TG-TUG to fit Garmin traditional dual beam / dual frequency transducer # 010-10272-00 or 010-10249-20
$139.00TG-TUG is Ideal for Installing on a trolling motor. It can also be attached on the side of a jack plate or on the boat set back with additional components.
-
AP-HDI-3 to fit Lowrance HDI (50/200kHz) 000-10977-001 xDucer on a Transom
$74.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-4 Spring Back Bracket # SBB-5. Please complete the questionnaire below when ordering this product.
-
Aluminum Skeg to fit Garmin Force Trolling Motor
$89.95AL-Skeg-Garmin 1/4″ Aircraft Aluminum Alloy, CNC Machined, Welded and Black Powder Coated.
“Aluminum vs Plastic” – Which one would you choose?
* Retrofit the plastic skeg with our Aluminum Skeg.
* Our Aluminum Skeg will also fit the optional Garmin Nose Cone with no built in sonar.
* Read more features and benefits ….. -
Mega 360 14-pin Transducer Y-Cable (14 M360 2DDI Y)
$74.95MEGA 360 14-pin Transducer Y-Cable
Humminbird Part # 14 M360 2DDI Y (720108-1)
-
Perspective Mode L Bracket – Garmin Panoptix LiveScope LVS34 transducer on trolling motor shaft or any shaft
$39.95Perspective Mode L Bracket Mount used to adjust the position of your Garmin Panoptix LiveScope LVS34 transducer on a trolling motor shaft or any shaft. This item is used along with your Garmin transducer mounting bracket.
-
TM-XTM-75/150 T to fit Humminbird XTM 9 HW MDI 75 T or XTM 9 HW MSI 150 T transducer
$99.95TM-XTM-75/150 T fits Humminbird® Helix Mega Di transducer XTM 9 HW MDI 75 T or Helix Mega Si transducer XM 9 HW MSI 150 T. for trolling motor, set back, hole shot plate or jack plate installation.
If this item is going on a Trolling Motor, please answer the trolling motor questions. If this item is going on the Jack Plate please answer all the questions about your jack plate and boat. It is very important that you answer the questionnaire in full please.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required. -
Spring-2 additional spring for SBB-4
$9.95Spring-2 is an additional stainless steel spring used along with our SBB-4 for larger transducers.
