Showing 13–24 of 160 results
-
Quest Trolling Motor Adaptor Plate
$40.00 – $81.85Item # Q-A-Plate – Quest Adaptor Plate is built in 6061 High Quality Aluminum Alloy and Black Powder Coated.
About our Adaptor Plate: the Adaptor Plate can be attached to a Transducer Shield which will allow you to attach the Transducer Shield to a Minnkota Quest Trolling Motor so that the clamps / straps are attached to the housing correctly.
About the Minnkota Quest Trolling Motor: the Minnkota Quest housing is configured differently to previous Minnkota models: 1. the skeg is off set ; 2. the shaft is larger on the housing; and 3. the US2 sonar is shaped differently to the previous Ultrex trolling motor.
The Good News is – if you already own one of our Transducer Shields simply purchase the Quest Adaptor Plate which will easily attach it to your previously purchased Transducer Shield (TM-H8.3, TG-HG-8.5, TS-AIHD-TS or TS-DSS3-TS).
On the longer TS-DSS3-TS and TS-AIHD-TS Transducer Shields, it will be necessary to purchase an additonal component “Ram” to close the gap between the US2 cone and the Transducer Shield. When placing your order, please select the Adaptor Plate with a Ram.
The Quest Adaptor Plate cannot be used with a transducer only, it must be attached to a Transducer Shield.Another Cool Product Proudly Designed in USA
See More Fish ………. Catch More Fish
-
Garmin Force Rail Kit
$99.95 -
-
Humminbird Target Lock Accessory Bracket Item # ACC-TL
$199.00Item # ACC-TL “Accessory Target Lock” is built in 6061 aircraft aluminum and black powder coated.
This item would be used in conjunction with our Receiver Ring system to attach a Humminbird® Target Lock to a Garmin®Force, Lowrance® Ghost or Minnkota® Ultrex trolling motor.When our Target Lock Bracket ACC-TL is attached to a Receiver Ring it can be on the left or the right side of the trolling motor.
The Receiver Ring attaches to the trolling motor head and one or two accessories can then be attached.
For example to attach a Humminbird® Mega 360 plus a Humminbird® Target Lock to an Ultrex Trolling Motor, the following products can be used:
ACC-RR-ULT + ACC-TL + ACC-RR-30When placing your order, please choose the correct Receiver Ring for your type of trolling motor.
Our Products are Proudly designed and built in the USA
See More Fish ………. Catch More Fish
-
B-SQUARE-CM with Cable Management
$29.95Item # B-SQUARE-CM This 3.5″ x 3.5″ x 3/4″ black polyethylene base with built-in-cable management creates a barrier between the fiberglass and metal electronic mount base.
-
Do’Nut Trolling Motor Rod Support
$14.95Trolling Motor Support Rod DO’NUT fits Minnkota Trolling Motors
1/2″ Black Polyethylene Marine Board x 2-1/4 Diameter and attaches to the deck with three (3) # 8 x 1″ stainless steel phillips pan head screws which are included in the package.
-
WC 2.5″ x 2.75″ x 0.5″ cable management cover
$19.95Black polyethylene marine board and is 2-1/2″ x 2-3/4″ x 1/2″ thick and includes stainless steel screws..
-
TS-AIHD-TS fits Lowrance® ActiveImaging HD™ or FishReveal
$199.00Item # TS-AIHD-TS is designed to fit Lowrance® Active Imaging HD™ 3-in-1 Transducer # 000-16062-001 (approx. 10-1/4” long x 2” wide x 1-1/4” thick and the cable comes out from the back).
It is formatted for installation on the side of the jack plate, hole shot plate or set back. If you are interested in installing to your transom, please see our Armor Plates.
-
TS-AIHD-TS Combo fits Lowrance® ActiveImaging HD™ transducer # 000-16062-001 or ActiveImaging HD™ FishReveal transducer # 000-16060-001 on a trolling motor
$225.95Item # TS-AIHD-TS Combo is built in High Quality Aluminum Alloy and Black Powder Coated for Trolling Motor installation. It is designed to fit Lowrance® ActiveImaging HD™ transducer # 000-16062-001 or ActiveImaging HD™ transducer # 000-16060-001. The transducer is approx. 10-1/4” long x 2” wide x 1-1/2″ thick and the cable comes out on top near the back.
It is very important that you complete the questionnaire when ordering our products. The information you provide will help us to assist you better and avoid a delay in shipping your order.
-
Ram Rail Kit for small Minnkota Trolling Motors
$150.00The Ram Rail Kit includes Skeg, 2 stainless steel straps & hardware. The kit can only be installed on a MinnKota trolling motor that has the Prop & Skeg on opposite ends and when the transducer to be attached is too long for the space between the propeller and skeg.
A transducer cannot be attached directly to the Ram Rail Kit and must be purchased along with a specific Transducer Shield to suit your transducer. After purchasing the Ram Rail Kit, click on “Shields” and choose the Transducer Shield to suit your transducer.
This product can be used with most Humminbird, Garmin & Lowrance Transducer Shields made by Transducer Shield and Saver.
Proudly designed and built in USA
-
MK-Filler Block used to attach a Transducer Shield to a MinnKota Ultrex 36 volt with a Built in Down Image Transducer
$71.95Item # MK-UL-36-DI-Filler this item is used to attach a Transducer Shield to a 24v or 36v Minnkota “Ultrex” trolling motor with a built in Down Image transducer.
For 36 volt includes two 4.0” and one 6″ heavy duty stainless steel black powder coated straps.
This item must be attached to a Transducer Shield (sold separately) in order for this item to work on the trolling motor. After ordering the Filler, please Click on Shields to choose the correct Transducer Shield to suit your transducer.
Proudly Designed and Built in USA
See More Fish ………. Catch More Fish
