Showing 145–152 of 152 results
-
WG-1 Wedge to attach a Transducer Shield to a Set Back or Hole Shot Plate
$14.95WG-1 Wedge along with a Transducer Shield will put the Transducer at the correct angle when the boat is in the water when installed on a Boat Set Back or Jack Plate hole shot/baffle plate
-
TM-HDsi fits Humminbird® HDSI xDucer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T
$79.95TM-HDSi fits Humminbird® High Definition Side Image Transducer XHS 9 HDSI 180 T or XTM 9 HDSI 180 T for trolling motor, set back or jack plate installation.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
TM-CSI-2 fits Humminbird Side Image XNT 9 SI 180 T, XNT 9 HW MSI 150 T or XNT 9 QB 90 T xDucer for Trolling Motor, Jack Plate or Set Back
$74.95Fits Humminbird® Compact Side Image XNT 9 SI 180T, XNT 9 HW MSI 150 T or Quad Beam XNT 9 QB 90 T transducer
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
-
Quick Clip
$3.95Stainless steel propeller safety clip. Never have to replace that rusted, broken or lost cotter pin again.
-
SSC-4 fits Humminbird XP 9 20 (T), XTM 9 20 T or XTM 14 20 T xDucers on a Trolling Motor
$29.95Fits Humminbird® Puck Transducer
XP 9 20 (T), XTM 9 20 T or XTM 14 20 T. This shield does not fit any of Humminbird’s side image transducers. -
SSC-3 fits Humminbird XNT 9 20 T or XNT 14 20 T xDucer on a Trolling Motor
$29.95To attach and protect your Humminbird® XNT 9 20 T or XNT 14 20 T (transom style) transducer on a Trolling Motor. (This Transducer Shield will not fit Humminbird Side Image Transducer # XNT 9 SI 180 T. Please see Transducer Shield # TM-CSI)
Please complete the information below when ordering this item.
-
SSC-2 fits Lowrance Pod PDT-WBL (106-74) transducer on a Trolling Motor
$29.95Fits Lowrance® Pod transducer PDT-WBL (106-74).
(With slight modifications, this Transducer Shield can be used for the Garmin® Pod transducer)
-
SSC-1 fits Lowrance HST-WSBL (106-72) 83/200kHz Skimmer transducer on a Trolling Motor
$29.95To attach and protect your Lowrance® Skimmer® HST-WSBL (106-72) Transducer on a Trolling Motor. (This shield will NOT fit Lowrance HDI transducer # 000-10976-001 or 000-10977-001 Please see Transducer Shield # TS-HDI-4 and TS-HDI-3) Please complete the information below when ordering this item.
