Showing 121–132 of 152 results
-
AP-CSi to fit a Humminbird Side Image xDucer XNT 9 SI 180 T or XNT 9 HW MSI 150 T on a Transom
$49.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket.
-
EXT-2.O” Extension
$35.00An extension between an L Bracket & Transducer Shield to lower the transducer so as to avoid side viewing signal interference with hull turning chines.
-
TS-LSS2-2L fits Lowrance LSS2 Structure Scan Transducer on a Set Back or Hole Shot Plate
$99.95Fits Lowrance LSS2 structure scan 10-1/4″ transducer for installation on SetBack/Step OR Hole Shot/Baffle plates.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
It is very important that you complete the questionnaire when ordering this item. -
AP-DI to fit a Humminbird Down Image xDucer XNT 9 DI T on a Transom
$49.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-4 Spring Back Bracket.
-
TS-LSS2-L fits Lowrance LSS2 Structure Scan Transducer on a Jack Plate
$169.00Easily attaches a Lowrance® LSS2 structure scan transducer, with ADDITIONAL components to your Jack Plate or Boat Set Back.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
It is VERY IMPORTANT that you complete the questionnaire when ordering this item.
-
TS-LSS2-3D fits Lowrance LSS2 Structure Scan & Pod xDucer together usually on a Trolling Motor
$224.95Transducer Shield to fit Lowrance LSS2 (10-1/4″) structure scan transducer and pod transducer in tandem on trolling motors. The information you provide will help us to assist you better and avoid a delay in shipping your order.
-
HW-Bracket-2 to attach a Hydro Wave speaker box to a Minnkota, Motorguide or Power Pole trolling motor shaft
$39.95High Quality Aluminum Bracket to securely attach a Hydro Wave Speaker Box to a trolling motor shaft.
Please complete the questionnaire when ordering this item.
It is VERY important that we know if your trolling motor is an MINNKOTA “ULTREX”
-
EXT-1.5″ Extension
$35.00Aluminum 1.5″ Extension attached to an L. Bracket and Transducer Shield to lower the level of the transducer. This item is sometimes required on Skeeter & Bass Cat boats.
-
Hydro Dynamics Rapid Jack
$49.95L. Adapter Bracket to fit Hydro Dynamics Rapid Jack jack plate. Used with a Transducer Shield to attach transducer to the side of the Jack Plate.
It is very important that you complete the questionnaire in full when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.
-
TS-DSI fits Lowrance DSI xDucer 000-10260-001 for Trolling Motor or Jack Plate install
$69.95Fits Lowrance Down Scan Skimmer transducer # 10260-001
not for use directly on transom. Please see additional accessories.
(Transducer is not included) -
LB-SM-6/8 for Slidemaster 6″ or 8″ Jack Plate
$49.95L. Adapter Bracket to fit Slide Master 6″ and 8″ manual Jack Plate. Used to attach a Transducer Shield to the side of the jack plate.
It is VERY IMPORTANT that you complete the questionnaire in full when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.
-
TM-DI fits Humminbird Down Image XNT 9 DI T xDucer for Trolling Motor, Jack Plate or Set Back
$74.95TM-DI fits Humminbird® Down Image Transducer # XNT 9 DI T for trolling motor, set back or jack plate installation. It DOES NOT fit the redesigned Down Image transducer # # XNT 9 DI T (RD). Onix Down Image Transducer XNT 14 DI T (RD) or XM 9 MDI T.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
