Showing 109–120 of 145 results
-
B-3-CM Base Plate with cable management
$24.95This 3/4″ black polyethylene 3″ round base with built-in cable management creates a barrier between the fiberglass & metal ram mount base.
-
B-4-CM-MAX Base Plate with cable management
$34.95This 4″ X 1″ black polyethylene round base with built-in cable management creates a barrier between the fiberglass & metal ram mount base.
-
MG-360-SLEEVE to attach Humminbird 360 to Motorguide outer shaft
$98.95MG-360-Sleeve Aluminum Sleeve used to fit a Humminbird 360 Imaging to a Motorguide Trolling Motor Outer Shaft. IMPORTANT NOTE: Some of the NEWER Motorguide trolling motors have the same size shaft as Minnkota and will not need the MG-360-SLEEVE when attaching a Humminbird 360.
-
AP-HDI-2 to fit Lowrance HDI (83/200kHz) 000-10976-001 xDucer on a Transom
$59.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket. Please complete the questionnaire below when ordering this product.
-
SBB-HDSI-Combo to attach Humminbird HDSI xDucer XHS 9 HDSI 180 T & Shield on a Transom
$194.95Spring Back Bracket and Transducer Shield TM-HDsi combination for transom installation. Ideal for boats with flat transoms or for boats without a jack plate.
-
LB-3-RW Blank L. Bracket – STARBOARD side
$49.95L. Bracket without pre-drilled holes used on T-H Marine Manual and Pro Hi Jacker 6, 8, 10 and 12″ jack plates and Bob’s 4″ or over 12″ Jack Plates.
-
AP-DSi to fit Lowrance DSI xDucer 000-10260-001 on a Transom
$49.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boat without a jack plate. Recommended as an added accessory to our SBB-4 Spring Back Bracket.
-
AP-CSi to fit a Humminbird Side Image xDucer XNT 9 SI 180 T or XNT 9 HW MSI 150 T on a Transom
$49.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and without a jack plate. Recommended as an added accessory to our SBB-5 Spring Back Bracket.
-
EXT-2.O” Extension
$35.00An extension between an L Bracket & Transducer Shield to lower the transducer so as to avoid side viewing signal interference with hull turning chines.
-
TS-LSS2-2L fits Lowrance LSS2 Structure Scan Transducer on a Set Back or Hole Shot Plate
$99.95Fits Lowrance LSS2 structure scan 10-1/4″ transducer for installation on SetBack/Step OR Hole Shot/Baffle plates.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
It is very important that you complete the questionnaire when ordering this item. -
AP-DI to fit a Humminbird Down Image xDucer XNT 9 DI T on a Transom
$49.95For transom installation to protect your transducer from side to side and front to back impact. Ideal for boats with flat transoms and for boats without a jack plate. Recommended as an added accessory to our SBB-4 Spring Back Bracket.
-
TS-LSS2-L fits Lowrance LSS2 Structure Scan Transducer on a Jack Plate
$169.00Easily attaches a Lowrance® LSS2 structure scan transducer, with ADDITIONAL components to your Jack Plate or Boat Set Back.
NOTE: When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water. For bottom reading on plane, a transducer inside the hull will be required.
It is VERY IMPORTANT that you complete the questionnaire when ordering this item.
