L Bracket is built in in High Quality Aluminum Alloy, Black Powder Coated and includes stainless steel hardware   This L Bracket is designed with a 3″ offset specifically for 8″, 10″ or 12″ Atlas Hydraulic Jack Plates.  The 3″ offset brings the Transducer Shield away from the Jack Plate so that the hydraulic trim rod does not interfere with, or damage the transducer or Transducer Shield® when moving up and down.  IMPORTANT & HELPFUL please open the link below to confirm the size of your jack plate

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.

(2)  An Extension is required if you have a Skeeter ZX or FX model boat.  The hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.  Click on Extensions to add an extension to your order.

(3)  Typically, a “Side Image” transducer attached to an L Bracket on the Side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane an “in hull” transducer is recommended.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 12″ Jack Plate – L3 (w/ offset)- PORT or PASSENGER SIDE first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-6-8-10-12-L to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-6-8-10-12-R to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate first appeared on Transducer Shield and Saver.

L Bracket is built in in High Quality Aluminum Alloy, Black Powder Coated and includes stainless steel hardware   This L Bracket is designed with a 3″ offset specifically for 8″, 10″ or 12″ Atlas Hydraulic Jack Plates.  The 3″ offset brings the Transducer Shield away from the Jack Plate so that the hydraulic trim rod does not interfere with, or damage the transducer or Transducer Shield® when moving up and down.  IMPORTANT & HELPFUL please open the link below to confirm the size of your jack plate

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.

(2)  An Extension is required if you have a Skeeter ZX or FX model boat.  The hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.  Click on Extensions to add an extension to your order.

(3)  Typically, a “Side Image” transducer attached to an L Bracket on the Side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane an “in hull” transducer is recommended.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 12″ Jack Plate – R3 (w/ offset) – for STARBOARD or DRIVER side first appeared on Transducer Shield and Saver.

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.
(2)  An Extension is required if you have a Skeeter ZX model boat.  On this particular boat, the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.

This L. Bracket can be used to attach a Transducer Shield to the side of an Atlas 8″, 10″ or 12″ Hydraulic Jack Plate BUT ONLY if your Transducer Shield and Atlas Jack Plate size is listed below.

GARMIN –
TG-D-Vu ~  8, 10 or 12” jack plate
TG-GT-6   ~ 10 or 12” jack plate
TG-DS-Vu ~ 12” jack plate
TG-DS-8.4 ~ 12” jack plate

HUMMINBIRD –
TM-HDsi   *  TM-DI-2 ~   8, 10 or 12” jack plate
TM-Csi   *  TM-DI  ~  6, 8, 10 or 12” jack plate
TM-HX-3 ~ 12” jack plate
TM-ONIX-1 ~ 10 or 12” jack plate
TM-ONIX-2 ~ 12” jack plate

LOWRANCE –
TS-LSS-1 ~ 10 or 12″ jack plate
TS-HDI-3  *  TS-HDI-4  *  TS-DSI  ~ 8, 10 or 12” jack plate

RAYMARINE –
TSS-RM-1  * TSS-RM-2 ~ 12” jack plate

If the Transducer Shield that you are installing on the side of your jack plate DOES NOT appear on the list above, please go to L Bracket # LB-AT-8.10.12-Combo (4” Jack Plate), L Bracket # LB-AT-6-R3 (6” Jack Plate) or L Bracket # LB-AT-8.10.12-R3 (8”, 10” or 12” Jack Plate)

                                         Proudly Designed and Built in the USA

                                         See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 14″ Jack Plate : L Bracket # LB-AT-4.6.8.10.12 (without offset) first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

Please choose one of the following Transducer Shields® to match your transducer:

(1)  Item # TM-Csi for Humminbird® compact side image transducer XNT 9 SI 180T

(2)  Item # TM-Di for Humminbird® down image transducer XNT 9 DI T

(3)  Item # TM-HDsi for Humminbird® high definition side image transducer           XHS HDSI 9 180 T

(4)  Item # TS-Dsi for Lowrance® down scan transducer

(5)  Item # TS-LSS-1 for Lowrance® Structure Scan LSS1 transducer

(6)  Item # TS-LSS2-L for Lowrance® Structure Scan LSS2 transducer

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-AT-4.6.8.10.12 to attach a Transducer Shield to ATLAS 8″ to 12″ jack plates first appeared on Transducer Shield and Saver.

A transducer cannot be attached to any of our L. Brackets without a Transducer Shield®.  When placing your order for this product, please remember to Click on the Shields tab to choose a Transducer Shield to suit your transducer when ordering an L Bracket.

Notes:

1.  If your Detwiler Jack Plate was installed by Bass Cat Boats spacers will be required.

2.  On Skeeter ZX or FX boats, the hull turning chines will interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield®.  Click on the Extension tab to add an extension to your order.

Typically, a “Side Image” transducer attached to an L Bracket on the side of a jack plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane, an “in hull” transducer is recommended.

Please complete the questionnaire when placing your order.  The more information that we have about your boat and jack plate, the better we can assist you.  Contact us if you need further assistance.

Proudly Designed and Built in the USA

See More Fish …….. Catch More Fish

The post LB-DETW-6.8.10 – L Bracket to attach a Transducer Shield to a Detwiler Jack Plate first appeared on Transducer Shield and Saver.

A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  Please add one of our Transducer Shields® to your shopping cart when ordering your L Bracket.  Go to Shields and pick the appropriate name brand and item to suit your transducer.

NOTE PLEASE:

(A)  Skeeter ZX or FX model boats, the hull turning chines interfere with the side viewing signal.  To overcome this problem add an Extension between the L Bracket and Transducer Shield:

Add a 2.0” extension when your transducer is a Lowrance® LSS1, LSS2, Total Scan, 2-in-1, 3-in-1 or 3D;

Add a 1.5” extension when the Transducer Shield is one of the following: Garmin TG-GT-6;  TG-DS-8.4;  TG-DS-9 or TG-HG-8.5 or Humminbird TM-HX-3, TM-H8.3, TM-H7.1 or Raymarine® Real Vision 3D transducer

(B)  Bass Cat Boats, if the Jack Plate was installed by Bass Cat, it is necessary to add a 1.5″ extension between the L Bracket and Transducer Shield.

Add an Extension to your order if (A) or (B) pertains to your application.  Contact us if you have questions.  We will be happy to assist you.

It is VERY IMPORTANT that you complete the questionnaire in full when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

All Products are Proudly Designed and Built in the USA

See More Fish ………. Catch More Fish

The post LB-SM-10/12 for Slidemaster 10″ or 12″ Jack Plate first appeared on Transducer Shield and Saver.