This Transducer Shield does not fit the new Garmin GT 36 or Garmin 56 transducer.

The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

For Trolling Motor installation, two straps are required and are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes.

WARNING:  Due to the size of the transducer and Transducer Shield on Minnkota up to 70 lb. thrust trolling motors (skeg & prop on opposite ends) and Motor Guide 55 lb. thrust and below, additional components may be required for a better fit on the trolling motor.

The TG-DS-Vu-2 is designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.  When purchasing this item to attach to your jack plate, please go to:

*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size

*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size

*  Go to Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.

*  Go to Spring Back Bracket # SBB-5 to install the transducer on the transom (if you do not have a jack plate)

*  Go to Armor Plate # AP-D/S-Vu (an additional option to the Spring Back Bracket)

NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

Proudly Designed and Built in the USA

Installing your Transducer Correctly is Important

The post TG-DS-Vu-2 to fit Garmin GT34 first appeared on Transducer Shield and Saver.

The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

For Trolling Motor installation, two straps are required which are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes to suit your particular trolling motor.

This Transducer Shield is also designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.

When purchasing this item to attach to your jack plate, please go to:

*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size

*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size

*  Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.

If you do not have a Jack Plate, you do not need our TG-TUG shield GO TO:

*  Spring Back Bracket # SBB-5 to install the transducer on the transom

*  Armor Plate # AP-GAR

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish   ……….   Catch More Fish

The post TG-TUG to fit Garmin traditional dual beam / dual frequency transducer # 010-10272-00 or 010-10249-20 first appeared on Transducer Shield and Saver.

This Transducer Shield includes two Stainless Black Powder Coated heavy duty straps, a custom ram or strip or ram and strip.  This will depend on your particular trolling motor.  The sleek hydrodynamic design will cut through the water for less drag,

On Minnkota Trolling Motors 70 lb thrust and below, with prop at the front of the housing will require an additional custom kit to attach Item # TG-GT30-3D to the trolling motor.  The custom item @ $150.00 is not available on line and must be ordered by phone.  Please call  334.514.7147 to place your order.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post TG-GT30-3D Transducer Shield to fit Garmin DownVü/SideVü GT30 and Pod GT8HW transducers together first appeared on Transducer Shield and Saver.

Item # AP-GT-6 is built in High Quality Aluminum Alloy and Black Powder Coated for installation on the boat transom.  It is designed to protect the transducer from side to side as well as front to back impact.  If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required if the transducer angle needs to be adjusted.

Our Armor Plates are designed as an added attachment to our SBB-5 Spring Back Bracket for all around transducer protection.  Please consider ordering an SBB-5 when ordering the Armor Plate.

To ensure that you are ordering the correct Armor Plate, please enlarge the images for transducer recognition.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA
See More Fish …… Catch More Fish

The post AP-GT-6 to fit Garmin GT 22, GT 24, GT 52 or GT 54 first appeared on Transducer Shield and Saver.

The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

For Trolling Motor installation, two straps are required which are not included and should be purchased separately.   Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes to suit your trolling motor.

WARNING:  Trolling Motors 12v or 24v 70 lb and below additional custom items will be required for the Total Scan transducer to fit.  Pricing will depend on your particular trolling motor.  When placing an order for this product, please make sure that you answer all the questions in the questionnaire.  From the information you provide we can determine if additional parts are required and you will be contacted.

Item TG-GT-6 along with additional components can easily be bolted to (a) the side of a Jack Plate or (b) on the Hole Shot Plate under the Jack Plate or (c) on the boat set back (under the transom).  The Transducer Shield must be attached to an L Bracket or Wedge for (a), (b) or (c) installation.

ADDITIONAL COMPONENTS required when placing the TG-GT-6 Transducer Shield for the following installation options:

(a)  on the side of a Jack Plate – Please go to L Brackets

(b)  on the Hole Shot Plate under the Jack Plate – Please go to Wedges

(c)  on the Transom Set Back – Please go to Wedges

*** If your boat does not have a Jack Plate or Set Back and you must attach your transducer to the back of the boat on the transom – Please go to Spring Back Bracket Item # SBB-5 and Armor Plate Item # AP-GT-6.

Please be aware that when installing a GT 22, GT 24, GT 52 or GT 54 transducer at the back of the boat, the transducer will lose the signal when the boat is up on plane.  To track the bottom when the boat is up on plane, a thru hull transducer may be required.  See your Garmin® owner manual or Garmin directly for additional information.

NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

All of the Products are Proudly Designed and Built in the USA
See More Fish …… Catch More Fish

The post TG-GT-6 to fit Garmin GT22, GT24, GT52 or GT54 first appeared on Transducer Shield and Saver.

The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal..

For Trolling Motor installation, two straps are required and are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes.

WARNING:  Due to the size of the transducer and Transducer Shield, when installed on a trolling motor, additional components may be required for a better fit on the trolling motor. If your trolling motor has the skeg at the front you will need a Ram Rail Kit @ $150.00 in addition to the Transducer Shield.  Please call for assistance.

The TG-DS-9 is designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.  When purchasing this item to attach to your jack plate, please go to:

*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size

*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size

*  Go to Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.

*  Go to Spring Back Bracket # SBB-5 to install the transducer on the transom (if you do not have a jack plate)

*  Go to Armor Plate # AP-DS-9  this is in addition to the Spring Back Bracket

NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

Installing your Transducer Correctly is Important

See More Fish    ……    Catch More Fish

The post TG-DS-9 fits Garmin GT21, GT23, GT41, GT50 and GT51 first appeared on Transducer Shield and Saver.

^{The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.}

^{For Trolling Motor installation, two straps are required and are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes.}

^{WARNING:  Due to the size of the transducer and Transducer Shield when installed on a trolling motor additional components will be required , for a  better fit on the trolling motor. Please call for assistance.}

^{The TG-DS-8.4 is designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.  When purchasing this item to attach to your jack plate, please go to:
*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size
*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size
*  Go to Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.
*  Go to Spring Back Bracket # SBB-5 to install the transducer on the transom (if you do not have a jack plate)
*  Go to Armor Plate # AP-DS-8.4 (an additional option to the Spring Back Bracket)     It is important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.}

Proudly Designed and Built in the USA

Installing your Transducer Correctly is Important

See More Fish    ……    Catch More Fish

The post TG-DS-8.4 fits Garmin GT40 first appeared on Transducer Shield and Saver.

Our Armor Plates are designed to protect your transducer from side to side as well as front and back impact. They are designed as an added attachment to our SBB-5 Spring Back Bracket for all around transducer protection.  Consider ordering an SBB-4 when ordering the Armor Plate.

If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required, if the transducer angle needs to be adjusted.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post AP-DS-Vu to fit Garmin GT30 and GT34 first appeared on Transducer Shield and Saver.

This Transducer Shield does not fit the new Garmin GT 36 or Garmin 56 transducer.

The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

For Trolling Motor installation, two straps are required and are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes.

WARNING:  Due to the size of the transducer and Transducer Shield on Minnkota up to 70 lb. thrust trolling motors (skeg & prop on opposite ends) and Motor Guide 55 lb. thrust and below, additional components may be required for a better fit on the trolling motor.

The TG-DS-Vu is designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.  When purchasing this item to attach to your jack plate, please go to:

*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size

*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size

*  Go to Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.

*  Go to Spring Back Bracket # SBB-5 to install the transducer on the transom (if you do not have a jack plate)

*  Go to Armor Plate # AP-D/S-Vu (an additional option to the Spring Back Bracket)

NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

Proudly Designed and Built in the USA

Installing your Transducer Correctly is Important

The post TG-DS-Vu to fit Garmin GT30 first appeared on Transducer Shield and Saver.

The sleek hydrodynamic design will cut through the water for less drag, especially on trolling motor application, reduce collection of debris and keep the transducer positioned correctly and will not interfere with the transducer signal.  Two straps (not included) are required to attach the Transducer Shield to a trolling motor.  When placing your order please consider purchasing two heavy duty stainless steel black powder coated straps @ $5.95 each.

WARNING: for Minnkota 12v & 24v 70 lb thrust and below (prop & skeg on opposite ends) AND Motorguide 12v & 24v 55 lb thrust and below, additional components may be required.

Item TG-D-Vu along with additional accessories, can easily be bolted to the side of a jack plate OR on the hole shot plate under the jack plate OR on a boat set back.  For more information, please go to L Brackets or Wedges.

Optional Accessories:

1.  L Bracket to install the Transducer Shield to the side of a Jack Plate

2.  Go to Wedges to install the Transducer Shield on the Hull Set Back

3.  Go to Wedges to install the Transducer Shield on the Hole Shot Plate under the jack plate

4.  Go to Spring Back Bracket # SBB-5 to install the transducer on the transom.  No Transducer Shield is required for this application.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post TG-D-Vü fits Garmin GT20 first appeared on Transducer Shield and Saver.