L Bracket is built in in High Quality Aluminum Alloy, Black Powder Coated and includes stainless steel hardware   This L Bracket is designed with a 3″ offset specifically for 8″, 10″ or 12″ Atlas Hydraulic Jack Plates.  The 3″ offset brings the Transducer Shield away from the Jack Plate so that the hydraulic trim rod does not interfere with, or damage the transducer or Transducer Shield® when moving up and down.  IMPORTANT & HELPFUL please open the link below to confirm the size of your jack plate

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.

(2)  An Extension is required if you have a Skeeter ZX or FX model boat.  The hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.  Click on Extensions to add an extension to your order.

(3)  Typically, a “Side Image” transducer attached to an L Bracket on the Side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane an “in hull” transducer is recommended.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 12″ Jack Plate – L3 (w/ offset)- PORT or PASSENGER SIDE first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-6-8-10-12-L to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-6-8-10-12-R to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-4-R to attach a Transducer Shield to Sea Star 4″ jack plate first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-4-L to attach a Transducer Shield to Sea Star 4″ jack plate first appeared on Transducer Shield and Saver.

The post “The Wedge” – Trolling Motor Shallow Water Bracket first appeared on Transducer Shield and Saver.

L Bracket is built in in High Quality Aluminum Alloy, Black Powder Coated and includes stainless steel hardware   This L Bracket is designed with a 3″ offset specifically for 8″, 10″ or 12″ Atlas Hydraulic Jack Plates.  The 3″ offset brings the Transducer Shield away from the Jack Plate so that the hydraulic trim rod does not interfere with, or damage the transducer or Transducer Shield® when moving up and down.  IMPORTANT & HELPFUL please open the link below to confirm the size of your jack plate

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.

(2)  An Extension is required if you have a Skeeter ZX or FX model boat.  The hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.  Click on Extensions to add an extension to your order.

(3)  Typically, a “Side Image” transducer attached to an L Bracket on the Side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane an “in hull” transducer is recommended.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 12″ Jack Plate – R3 (w/ offset) – for STARBOARD or DRIVER side first appeared on Transducer Shield and Saver.

CMC jack plates are ridged or flat and have large bolt heads protruding out from the jack plate surface. This is why the L Bracket should include 1″ or 1.5″ spacers. Depending on the jack plate (usually manual) height position, the ratchet bolt might hang below the bottom of the jack plate  If this applies to your jack plate, it may be necessary to lower the transducer to avoid side signal interference. To do this, simply add an EXTENSION between the L Bracket and Transducer Shield.             

A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.                        

To avoid a delay in shipping your order, please complete the questionnaire. The more information you provide the better we can assist you.

IMPORTANT:  On Skeeter ZX or FX  boats, the hull turning chines interfere with the side viewing signal. To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield®. Please remember to add an Extension to your order.   Click on Extensions to add an extension to your order.

Typically, a “Side Image” transducer attached to an L Bracket on the side of a jack plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane, an “in hull” transducer is recommended.

Installing Your Transducer Correctly is Important.  Contact us if you need further assistance.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post LB-CMC-5/5-8 to fit 5.5 to 8″ CMC Jack Plate first appeared on Transducer Shield and Saver.

It is pre-drilled to match the hole pattern on our L Brackets and Transducers Shields for easy install.

When placing an order for an extension, please remember to order a Transducer Shield® and L Bracket to suit your transducer and jack plate.

The post EXT-3.0 Extension first appeared on Transducer Shield and Saver.

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.
(2)  An Extension is required if you have a Skeeter ZX model boat.  On this particular boat, the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.

This L. Bracket can be used to attach a Transducer Shield to the side of an Atlas 8″, 10″ or 12″ Hydraulic Jack Plate BUT ONLY if your Transducer Shield and Atlas Jack Plate size is listed below.

GARMIN –
TG-D-Vu ~  8, 10 or 12” jack plate
TG-GT-6   ~ 10 or 12” jack plate
TG-DS-Vu ~ 12” jack plate
TG-DS-8.4 ~ 12” jack plate

HUMMINBIRD –
TM-HDsi   *  TM-DI-2 ~   8, 10 or 12” jack plate
TM-Csi   *  TM-DI  ~  6, 8, 10 or 12” jack plate
TM-HX-3 ~ 12” jack plate
TM-ONIX-1 ~ 10 or 12” jack plate
TM-ONIX-2 ~ 12” jack plate

LOWRANCE –
TS-LSS-1 ~ 10 or 12″ jack plate
TS-HDI-3  *  TS-HDI-4  *  TS-DSI  ~ 8, 10 or 12” jack plate

RAYMARINE –
TSS-RM-1  * TSS-RM-2 ~ 12” jack plate

If the Transducer Shield that you are installing on the side of your jack plate DOES NOT appear on the list above, please go to L Bracket # LB-AT-8.10.12-Combo (4” Jack Plate), L Bracket # LB-AT-6-R3 (6” Jack Plate) or L Bracket # LB-AT-8.10.12-R3 (8”, 10” or 12” Jack Plate)

                                         Proudly Designed and Built in the USA

                                         See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 14″ Jack Plate : L Bracket # LB-AT-4.6.8.10.12 (without offset) first appeared on Transducer Shield and Saver.