This Transducer Shield does not fit the new Garmin GT 36 or Garmin 56 transducer.

The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

For Trolling Motor installation, two straps are required and are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes.

WARNING:  Due to the size of the transducer and Transducer Shield on Minnkota up to 70 lb. thrust trolling motors (skeg & prop on opposite ends) and Motor Guide 55 lb. thrust and below, additional components may be required for a better fit on the trolling motor.

The TG-DS-Vu-2 is designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.  When purchasing this item to attach to your jack plate, please go to:

*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size

*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size

*  Go to Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.

*  Go to Spring Back Bracket # SBB-5 to install the transducer on the transom (if you do not have a jack plate)

*  Go to Armor Plate # AP-D/S-Vu (an additional option to the Spring Back Bracket)

NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

Proudly Designed and Built in the USA

Installing your Transducer Correctly is Important

The post TG-DS-Vu-2 to fit Garmin GT34 first appeared on Transducer Shield and Saver.

The post “The Wedge” – Trolling Motor Shallow Water Bracket first appeared on Transducer Shield and Saver.

^{The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.}

^{For Trolling Motor installation, two straps are required which are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes.}

^{WARNING:  Due to the size of the transducer and Transducer Shield, when installed on a trolling motor, additional components may be required for a better fit on the trolling motor. If your trolling motor has the skeg at the front you will need a Ram Rail Kit @ $150.00 in addition to the Transducer Shield.  Please call for assistance.}

^{The TG-HG-8.5 is designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.  When purchasing this item to attach to your jack plate, please go to:}

^{*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size}

^{*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size}

^{*  Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.}

^{*  Spring Back Bracket # SBB-5 to install the transducer on the transom (if you do not have a jack plate)}

^{*  Armor Plate # AP-DS-8.4 this is in addition to the Spring Back Bracket}

Proudly Designed and Built in the USA

The post TG-HG-8.5 Transducer Shield to fit Garmin GT 56 or GT 36 first appeared on Transducer Shield and Saver.

Features and Benefits:  

*  Built in grass cutter will keep the hub free from grass or aquatic vegetation.

*  More efficient on turns

*  Skeg is positioned closer to the prop for maximum protection

*  Placement of our aluminum skeg creates a larger area to fit a variety of Transducer Shields and other Xducers to the trolling motor housing

*  Will fit the optional Garmin Nose Cone with no built in sonar

*  Includes Stainless M5 machine screws

*  Easy do-it-yourself Installation

Proudly Designed and Built in USA

Thank You for Your Purchase

The post Aluminum Skeg to fit Garmin Force Trolling Motor first appeared on Transducer Shield and Saver.

Our Armor Plates are designed to protect your transducer from side to side as well as front and back impact.  They are designed as an added attachment to our SBB-4 Spring Back Bracket for all around transducer protection.  Consider ordering a Spring Back Bracket when ordering the Armor Plate.

If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required, if the transducer angle needs to be adjusted.

Is is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post AP-GAR-2 to Fit Garmin Dual Beam transducer first appeared on Transducer Shield and Saver.

Item # AP-GT-6 is built in High Quality Aluminum Alloy and Black Powder Coated for installation on the boat transom.  It is designed to protect the transducer from side to side as well as front to back impact.  If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required if the transducer angle needs to be adjusted.

Our Armor Plates are designed as an added attachment to our SBB-5 Spring Back Bracket for all around transducer protection.  Please consider ordering an SBB-5 when ordering the Armor Plate.

To ensure that you are ordering the correct Armor Plate, please enlarge the images for transducer recognition.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA
See More Fish …… Catch More Fish

The post AP-GT-6 to fit Garmin GT 22, GT 24, GT 52 or GT 54 first appeared on Transducer Shield and Saver.

An Armor Plate is designed to protect the transducer from side to side as well as front and back impact. It takes the place of the factory transom mounting bracket.  If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required if the angle needs to be adjusted.

An Armor Plate is also designed to attach to our Spring Back Bracket # SBB-5 for all around transducer protection.   If an Armor Plate breaks, which has been attached to the boat, without a Spring Back Bracket, it has no warranty whatsoever.

Proudly Designed and Built in the USA

The post AP-DS-9 to fit Garmin GT41, GT50 & GT51 first appeared on Transducer Shield and Saver.

Our Armor Plates are designed to protect your transducer from side to side as well as front and back impact. They are designed as an added attachment to our SBB-5 Spring Back Bracket for all around transducer protection.  Consider ordering an SBB-4 when ordering the Armor Plate.

If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required, if the transducer angle needs to be adjusted.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post AP-DS-Vu to fit Garmin GT30 and GT34 first appeared on Transducer Shield and Saver.

Our Armor Plates are designed to protect your transducer from side to side as well as front and back impact.  They are designed as an added attachment to our SBB-5 Spring Back Bracket for all around transducer protection.  Consider ordering a Spring Back Bracket when ordering the Armor Plate.

If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required, if the transducer angle needs to be adjusted.

Is is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post AP-D-Vu to fit Garmin GT20 first appeared on Transducer Shield and Saver.

This Transducer Shield does not fit the new Garmin GT 36 or Garmin 56 transducer.

The Transducer Shield’s sleek hydrodynamic design will cut through the water for less drag especially on trolling motors.  It reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

For Trolling Motor installation, two straps are required and are not included.  Optional:  HDTS-B heavy duty black powder coated stainless steel straps @ $5.95 each and available in three sizes.

WARNING:  Due to the size of the transducer and Transducer Shield on Minnkota up to 70 lb. thrust trolling motors (skeg & prop on opposite ends) and Motor Guide 55 lb. thrust and below, additional components may be required for a better fit on the trolling motor.

The TG-DS-Vu is designed to easily attach to one of our L Brackets or Wedges for Jack Plate, Hole Shot Plate or Set Back installation.  When purchasing this item to attach to your jack plate, please go to:

*  L Brackets for install on the side of the jack plate – choose by jack plate brand and size

*  Wedges for install on the hole shot plate under the jack plate – choose by jack plate brand and size

*  Go to Wedges for install under the transom set back – if your boat does not have a flat set back, this is not a good option for you.

*  Go to Spring Back Bracket # SBB-5 to install the transducer on the transom (if you do not have a jack plate)

*  Go to Armor Plate # AP-D/S-Vu (an additional option to the Spring Back Bracket)

NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.

Proudly Designed and Built in the USA

Installing your Transducer Correctly is Important

The post TG-DS-Vu to fit Garmin GT30 first appeared on Transducer Shield and Saver.