L Bracket is built in in High Quality Aluminum Alloy, Black Powder Coated and includes stainless steel hardware   This L Bracket is designed with a 3″ offset specifically for 8″, 10″ or 12″ Atlas Hydraulic Jack Plates.  The 3″ offset brings the Transducer Shield away from the Jack Plate so that the hydraulic trim rod does not interfere with, or damage the transducer or Transducer Shield® when moving up and down.  IMPORTANT & HELPFUL please open the link below to confirm the size of your jack plate

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.

(2)  An Extension is required if you have a Skeeter ZX or FX model boat.  The hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.  Click on Extensions to add an extension to your order.

(3)  Typically, a “Side Image” transducer attached to an L Bracket on the Side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane an “in hull” transducer is recommended.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 12″ Jack Plate – L3 (w/ offset)- PORT or PASSENGER SIDE first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-6-8-10-12-L to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-6-8-10-12-R to attach a Transducer Shield to Sea Star 6, 8, 10, 12″ jack plate first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-4-R to attach a Transducer Shield to Sea Star 4″ jack plate first appeared on Transducer Shield and Saver.

Built in High Quality Aluminum Alloy and Black Powder Coated.  The L. Bracket is angled to put the transducer at the correct angle when the boat is in the water.

You will also need to order the correct Transducer Shields® to match your transducer:

NOTE PLEASE:

Go to and add an Extension to your order if you have a Skeeter ZX model boat.  Reason:  the hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield.

The post LB-SS-4-L to attach a Transducer Shield to Sea Star 4″ jack plate first appeared on Transducer Shield and Saver.

The post “The Wedge” – Trolling Motor Shallow Water Bracket first appeared on Transducer Shield and Saver.

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.

(2)  An Extension is required if you have a Skeeter ZX or FX model boat.  The hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.   Click on Extensions to add an extension to your order.

(3)  Typically, a “Side Image” transducer attached to an L Bracket on the Side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane an “in hull” transducer is recommended.

All of our Transducer Shields being attached to a 4″ Atlas Jack Plate will require this L Bracket with a Solid Spacer.  For your convenience our Transducer Shields are listed below.

Humminbird –   * TM-H7.1  * TM-H8.3  * TM-HX-3  * TM-ONIX-1  * TM-ONIX-2  * TM-Csi-2  * TM-Di  * TM-DI-2  * TM-HDSI

Garmin –  TG-D-Vu  * TG-D/S-Vu  * TG-GT-6  * TG-DS-8.4 * TG-HG-8.5 * TG-DS-9

Lowrance –   * TS-TRI-SH  * TS-AIHD-TS  * TS-DSS3-TS  * TS-HDI-4 * TS-HDI-3  * TS-LSS-1  * TS-LSS-3D  * TS-LSS2-L  * TS-LSS2-3D * TS-SP-SH  * TS-DSi

Raymarine –  TSS-RM-1 (dragonfly)  * TSS-RM-2

It is very important that you complete the questionnaire in full when ordering any of our products.  The information you provide will help us to assist you better and avoid a delay in shipping your order. The more information that we have about your boat and jack plate, the better we can assist you.  Contact us if you need further assistance.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post Atlas 4″ Jack Plate – L Bracket # LB-AT-4-Combo (with solid spacer) first appeared on Transducer Shield and Saver.

L Bracket is built in in High Quality Aluminum Alloy, Black Powder Coated and includes stainless steel hardware   This L Bracket is designed with a 3″ offset specifically for 8″, 10″ or 12″ Atlas Hydraulic Jack Plates.  The 3″ offset brings the Transducer Shield away from the Jack Plate so that the hydraulic trim rod does not interfere with, or damage the transducer or Transducer Shield® when moving up and down.  IMPORTANT & HELPFUL please open the link below to confirm the size of your jack plate

Atlas Jack Plate – Measuring Guide

PLEASE NOTE:
(1)  A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.

(2)  An Extension is required if you have a Skeeter ZX or FX model boat.  The hull turning chines interfere with the side viewing signal.  To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield to lower the transducer.  Click on Extensions to add an extension to your order.

(3)  Typically, a “Side Image” transducer attached to an L Bracket on the Side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane an “in hull” transducer is recommended.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post ATLAS 8″ to 12″ Jack Plate – R3 (w/ offset) – for STARBOARD or DRIVER side first appeared on Transducer Shield and Saver.

Typically, a “Side Image” transducer attached to an L Bracket on the side of a Jack Plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plan, an “in hull” transducer is recommended.

When ordering for a Rite Hite jack plate, there are measurements that we may need to know. Reason:  Rite Hite is made up of four pieces of angle iron (2 on each side) and one tube which joins the pieces together.  If the angle iron at the back (engine side) is lower than the angle iron at the front (transom) it will be necessary to add an Extender Plate to the L Bracket.  The Extender Plate is used to fill the void between the two sides.  Please see the photos to help in understanding the complexity of this particular type of jack plate.
L Bracket Item # LB-RH-6 is $54.95
Extender Plate Item # RH-EXT-Plate is $49.00  If your jack plate requires the Extender Plate, when placing your order, please click on the option and choose YES

It is VERY IMPORTANT that you complete the questionnaire in full when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish ………. Catch More Fish

The post Rite Hite L Bracket LB-RH-6 first appeared on Transducer Shield and Saver.

It is uniquely designed to fit an Airmar Transom TM150-T transducer.  Modifications will need to be made to the transducer for it fit into our Transducer Shield.  The alterations are shown in our instructions.

For trolling motor installation, two straps are required and are not included.  Heavy duty stainless steel, black powder coated straps are available @ $5.95 each.

With additional accessories, TM-AM-TM150-T can be bolted to the side of a Jack Plate, on the hole shot plate under the jack plate OR on a boat set back.  Go to L Brackets if bolting to side of the jack plate or go to Wedges if going on a hole shot plate or set back.

It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.  If you require further assistance, don’t hesitate to contact us.  We are happy to help.

Proudly Designed and Built in the USA

See More Fish ……… Catch More Fish

The post TM-AM-TM150-T to fit Airmar Transom transducer on Trolling Motor first appeared on Transducer Shield and Saver.