*  Sleek design in high quality 6061 aluminum alloy CNC machined and includes stainless steel hardware

*  Black Cerekoted to provide a robust shield against the elements

*  Precise “interlocking teeth” design allows you to rotate your transducer in 5-degree increments to fine tune the transducer angle in Forward or Down mode

*  Barrel Mount for Lowrance® Active Target™ or Garmin® Livescope™

*  Barrel Mount is designed to be installed on all trolling motor can rotate between Forward/Down and Perspective/Scout

*Include Cable Routing guide – Spring mounted fiberglass stick to ziptie your FFS cable to and make safely away from propeller!

Proudly Designed and Built in USA

See More Fish ……….   Catch More Fish

The post FFS Elite Bullet Mount for Live Sonar Transducers first appeared on Transducer Shield and Saver.

CMC jack plates are ridged or flat and have large bolt heads protruding out from the jack plate surface. This is why the L Bracket should include 1″ or 1.5″ spacers. Depending on the jack plate (usually manual) height position, the ratchet bolt might hang below the bottom of the jack plate  If this applies to your jack plate, it may be necessary to lower the transducer to avoid side signal interference. To do this, simply add an EXTENSION between the L Bracket and Transducer Shield.             

A transducer cannot be attached to any of our L Brackets without a Transducer Shield®.  When placing your order for this product, please remember to choose the appropriate Transducer Shield® to match your transducer.                        

To avoid a delay in shipping your order, please complete the questionnaire. The more information you provide the better we can assist you.

IMPORTANT:  On Skeeter ZX or FX  boats, the hull turning chines interfere with the side viewing signal. To help correct this problem it is necessary to add an extension between the L Bracket and Transducer Shield®. Please remember to add an Extension to your order.   Click on Extensions to add an extension to your order.

Typically, a “Side Image” transducer attached to an L Bracket on the side of a jack plate will not track the bottom when the boat is up on plane.  To track the bottom when up on plane, an “in hull” transducer is recommended.

Installing Your Transducer Correctly is Important.  Contact us if you need further assistance.

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post LB-CMC-5/5-8 to fit 5.5 to 8″ CMC Jack Plate first appeared on Transducer Shield and Saver.

It is pre-drilled to match the hole pattern on our L Brackets and Transducers Shields for easy install.

When placing an order for an extension, please remember to order a Transducer Shield® and L Bracket to suit your transducer and jack plate.

The post EXT-3.0 Extension first appeared on Transducer Shield and Saver.

An extension is necessary on most Skeeter ZX model boats to lower the level of the transducer, so that the transducer side signal clears the hull sponsons and/or turning chines.

An extension is also required on some jack plates that were installed on Bass Cat boats.  Reason:  the jack plate is longer and installed with 6 bolts to the transom rather than 4 bolts.

When placing an order for an extension, please remember to order a Transducer Shield® and L. Bracket to suit your transducer and jack plate.

Proudly Designed and Made in USA

The post EXT-2.O” Extension first appeared on Transducer Shield and Saver.

An extension is also required on some Jack Plates that were installed on Bass Cat boats.  Reason:  the jack plate is longer and installed with 6 bolts to the transom rather than 4 bolts. When placing an order for an extension, please remember to order a Transducer Shield® and L. Bracket to suit your transducer and jack plate.

Proudly Designed and Made in USA

The post EXT-1.5″ Extension first appeared on Transducer Shield and Saver.