For trolling motor installation go to TS-AIHD-TS-COMBO.

Item # TS-AIHD-TS is built-in High-Quality Aluminum Alloy and Black Powder Coated.

It is designed to fit Lowrance® Active Imaging HD™ 3-in-1 Transducer # 000-16062-001 or Active Imaging HD™ 3-in-1 Fish Reveal Transducer # 000-16060-001 (approx. 10-1/4” long x 2” wide x 1-1/2” thick and the cable comes out from the back). Also designed to fit # 003-32772-00. The Sleek Hydrodynamic Design will cut through the water for less drag, reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

Item # TS-AIHD-TS along with additional components can easily be bolted to (a) the side of a Jack Plate or (b) on the boat set back (under the transom).  The Transducer Shield must be attached to an L Bracket or Wedge for (a) or (b) installation.

NOTE:  When the transducer is attached to a Set Back or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required. See your Lowrance® owner manual for additional information.

ADDITIONAL COMPONENTS required when purchasing Item # TS-AIHD-TS:

(a)  on the side of a Jack Plate – Click on L Brackets
(b)  on the Transom Set Back –  Click on Wedges

*** If your boat does not have a Jack Plate or Set Back and you must attach your transducer to the back of the boat on the transom – Please go to Spring Back Bracket Item # SBB-5

NOTE: Lowrance made this transducer very similar in name as their other products, but with slightly different shapes.  Please see the photo guide below to ensure you are ordering the correct part needed. 

Our Products are Proudly Designed &

                 Built in the USA to Protect & Save

The post TS-AIHD-TS fits Lowrance® ActiveImaging HD™ or FishReveal first appeared on Transducer Shield and Saver.

The Sleek Hydrodynamic Design will cut through the water for less drag, reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

The Combo includes two Stainless Steel Black Powder coated straps and the appropriate finishing “Ram” and / or “Strip” required to fit Minnkota® and Motorguide® trolling motors 24v 74 lb and up.

Warming:  Minnkota and Motoguide Trolling Motors 70 lb thrust down to 43 lb thrust will require additional components due to the length of the trolling motor housing and size of the transducer.  Garmin Force trolling motors will also require additional components.  Custom parts and pricing will depend on your particular trolling motor.  When placing an order for this product, please make sure to answer all the questions in the questionnaire or call and we will help you over the phone.

Our Products are Proudly Designed and Built in Alabama

See More Fish ……….  Catch More Fish

The post TS-AIHD-TS Combo fits Lowrance® ActiveImaging HD™ transducer # 000-16062-001 or ActiveImaging HD™ FishReveal transducer # 000-16060-001 on a trolling motor first appeared on Transducer Shield and Saver.

NOTE: Lowrance made this transducer very similar in name and shape as some of their other transducers. Please see the below photo to ensure you are ordering the correct product.

^{An Armor Plate is designed to protect the transducer from side to side as well as front and back impact. An Armor Plate takes the place of the factory transom mounting bracket.  It is also designed to attach to our Spring Back Bracket # SBB-5 for all around transducer protection.
If the Armor Plate is installed anywhere other than on the transom, for example on the set back wall, some shimming may be required if the transducer angle needs to be adjusted.} 

^{A Spring Back Bracket # SBB-5 is recommended when ordering an Armor Plate for all around transducer protection.   If an Armor Plate breaks, which has been attached to the boat without a Spring Back Bracket, it has no warranty whatsoever.}

Our Products are Proudly Designed &

Built in the USA to Protect & Save

The post AP-TS-3D to fit Lowrance/Simrad Total Scan, LSS2, Structure Scan 3D, Total Scan, Live Active Imaging 2-in-1 or 3-in-1 transducer on a Transom first appeared on Transducer Shield and Saver.

Note:  This item is NOT recommended for the Lowrance® Structure Scan 3D transducer on a trolling motor. Reason: the 3D transducer would also need a 2D transducer.  We do not offer a Transducer Shield to accommodate two transducers.

The Sleek Hydrodynamic Design will cut through the water for less drag, reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.

The Combo includes two Stainless Steel Black Powder coated straps and the appropriate finishing “Ram” and / or “Strip” required to fit Minnkota® and Motorguide® trolling motors 24v 74 lb and up.

It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

Warming:  Minnkota and Motoguide Trolling Motors 70 lb thrust down to 43 lb thrust will require additional components due to the size of the transducer and length of the trolling motor housing. Custom parts and pricing will depend on your particular trolling motor.  When placing an order for this product, please make sure to answer all the questions in the questionnaire.  From the information you provide we will be able to determine if additional parts are required.  You will be contacted before the order is shipped.

OPTIONS:
If you plan to install the Total Scan transducer on the side of a Jack Plate, Hole Shot Plate under the Jack Plate or Set Back below the transom – Please go to Transducer Shield® Item # TS-DSS3-TS

If you plan to install the Total Scan transducer on the back of the boat (transom) – Please go to Spring Back Bracket Item # SBB-4 and Armor Plate Item # AP-TS-SS2-3D

All of the Products are Proudly Designed and Built in the USA
See More Fish …… Catch More Fish

The post TS-DSS3-TS Combo fits Lowrance® Total Scan & Live Active Imaging 2-in-1 or 3-in-1 xDucer on a Trolling Motor first appeared on Transducer Shield and Saver.

AP-HDI-2 will fit Lowrance® Elite Hybrid Dual Imaging Transducer # 000-10976-001 (83/200kHz).  It does not fit the larger 000-10977-001 (50/200kHz) Hybrid Dual Imaging Transducer.  To ensure that you are ordering the correct Armor Plate, please enlarge the images for transducer recognition. When ordering AP-HDI-2 Armor Plate, please provide your transducer number in the comment area to ensure that the correct item is chosen. The Armor Plate includes stainless steel hardware and easy Do-It Yourself instructions.  Your transducer factory bracket will not be required with an Armor Plate.

Our Armor Plates are designed as an added attachment to our Spring Back Bracket for all around transducer protection.  Please consider ordering a Spring Back Bracket # SBB-5 when purchasing the Armor Plate.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

See More Fish  ……….  Find More Fish

The post AP-HDI-2 to fit Lowrance HDI (83/200kHz) 000-10976-001 xDucer on a Transom first appeared on Transducer Shield and Saver.