_{About our Adaptor Plate:  the Adaptor Plate can be attached to a Transducer Shield which will allow you to attach the Transducer Shield to a Minnkota Quest Trolling Motor so that the clamps / straps are attached to the housing correctly.}

_{About the Minnkota Quest Trolling Motor:  the Minnkota Quest housing is configured differently to previous Minnkota models:  1. the skeg  is off set;  2. the shaft is larger on the housing; and  3.  the US2 sonar is shaped differently to the previous Ultrex trolling motor.
The Good News is - if you already own one of our Transducer Shields simply purchase the Quest Adaptor Plate which will easily attach it to your previously purchased Transducer Shield (TM-H8.3, TG-HG-8.5, TS-AIHD-TS or TS-DSS3-TS).
On the longer TS-DSS3-TS and TS-AIHD-TS Transducer Shields, it will be necessary to purchase an additional component "Ram" to close the gap between the US2 cone and the Transducer Shield.  When placing your order, please select the Adaptor Plate with a Ram.
The Quest Adaptor Plate cannot be used with a transducer only; it must be attached to a Transducer Shield.}

               Another Cool Product Proudly Designed in USA     

The post Quest Trolling Motor Adaptor Plate first appeared on Transducer Shield and Saver.

The post Ram Rail Kit for small Minnkota Trolling Motors first appeared on Transducer Shield and Saver.

^{TS-DSS3-TS to fit Lowrance®   *Total Scan  *2-in-1  * 3-in-1  *Structure Scan 3D}

^{TS-LSS2-L to fit Lowrance® LSS2 transducer}

^{TS-EAG-TS to fit Lowrance® Eagle Tripleshot transducer}

^{TM-HX-3 to fit Humminbird® MSI Transducer  * TM-H8.3 to fit Humminbird® G2N, G3N or G4N Transducer}

TG-DS-8.4 * TG-DS-9 or TG-HG-8.5 Transducer Shields

^{WG-LSS2 Wedge and Transducer Shield® assembly can be installed on a transom set-back or under a jack plate on the hole shot plate, on 10″ and above jack plates only.}

^{WG-LSS2 wedge is not a good candidate for jack plates that are built at a 90 degree angle with the transom.  It is also not a good candidate for jack plates less than 10″ wide.  For such jack plates we recommend installing the Transducer Shield on the side of the jack plate by adding an L Bracket to the Transducer Shield.  Choose an L Bracket to suit your Jack Plate brand and size.}

^{When purchasing this item please remember to order the appropriate Transducer Shield for your * Lowrance  * Humminbird or * Garmin transducer .} 

^{It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.}

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post WG-LSS2 to fit Humminbird TM-HX-3, TM-H8.3, TS-EAG-TS or Garmin TG-HG-8.5 Transducer Shield on Set Back or Hole Shot Plate (10-12″ jack plates only) first appeared on Transducer Shield and Saver.

Choose WG-3.5 wedge for the following Transducer Shield TM-HX-1 which fits Humminbird® Mega Transducer # XM 9 20 MSI T or Solix Transducer # XM 14 20 MSI T

It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

The post WG-3.5 Wedge used to attach TM-HX-1 Transducer Shield to a 90 degree Hole Shot Plate first appeared on Transducer Shield and Saver.

Choose LWG-3 wedge for the following Transducer Shields: Garmin: TG-DS-Vu or TG-DS-8.4  and  Humminbird:  TM-ONIX-1, TM-ONIX-2 or TM-HX-1  and  Raymarine:  TSS-RM-1 or TSS-RM-2

A Transducer Shield® and Wedge assembled together will enable you to attach a transducer to a hull set back/step OR hole shot plate/baffle plate under a jack plate.  This wedge is NOT suitable for hole shot plates that are at a 90º angle with the transom.  For such jack plates, we recommend WG-2.5 Wedge or use an L Bracket to attach the Transducer Shield to the side of the jack plate.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

Installing Your Transducer Correctly is Important

See More Fish    ……    Catch More Fish

The post LWG-3 Wedge for Hole Shot or Set Back install first appeared on Transducer Shield and Saver.

^{WG-LSS2 Wedge and Transducer Shield® assembly can be installed on a transom set-back or under a jack plate on the hole shot plate, on 10″ and above jack plates only.}

^{WG-LSS2 wedge is not a good candidate for jack plates that are built at a 90 degree angle with the transom.  It is also not a good candidate for jack plates less than 10″ wide.  For such jack plates we recommend installing the LSS2 Structure Scan transducer on the side of the jack plate by adding an L Bracket to the Transducer Shield.  Choose an L Bracket to suit your Jack Plate brand and size.}

^{When purchasing this item please remember to order the appropriate Transducer Shield for your Lowrance LSS2 (TS-LSS2-L), Total Scan, 2-in-1, 3-in-1 or Structure Scan 3D Transducer (TS-DSS3-TS).} 

^{It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.}

Proudly Designed and Built in the USA

See More Fish    ……    Catch More Fish

The post WG-LSS2 to fit Lowrance LSS2, Total Scan, 3-on-1, 2-in-1, Structure Scan 3D Humminbird TM-HX-3 or TM-H8.3 on Set Back or Hole Shot Plate (10-12″ jack plates only) first appeared on Transducer Shield and Saver.

^{NOTE:  When the transducer is attached to a Set Back, Hole Shot Plate or the side of a Jack Plate, it will not track the bottom when up on plane because the transducer is out of the water.  For bottom reading on plane, a transducer inside the hull will be required.}

_{The Sleek Hydrodynamic Design will cut through the water for less drag, reduces collection of debris, keeps the transducer positioned correctly and will not interfere with the transducer signal.}

_{Item TS-LSS2-L along with additional accessories can easily be bolted to the side of a Jack Plate, on the Hole Shot Plate under the Jack Plate, OR on the boat set back. For this installation, please see L Brackets or Wedges. When installing a Structure Scan transducer it is important to be aware that an in hull transducer will also be required. The Structure Scan transducer signal picks up trees and structure etc. A pod or skimmer transducer will pick up fish, depth and will separate the fish from the structure. Resulting in the best performance when the boat is up on plane.}

_{Item TS-LSS2-L is approximately 10-1/2” long and cannot be installed on a trolling motor.  If you were planning on installing an LSS2 transducer on your trolling motor,  then please see Item # TS-LSS2-3D.}

_{It is very important that you complete the questionnaire when ordering this item. The information you provide will help us to assist you better and avoid a delay in shipping your order.}

Proudly Designed and Built in the USA
See More Fish …… Catch More Fish

The post TS-LSS2-L fits Lowrance LSS2 Structure Scan Transducer on a Jack Plate first appeared on Transducer Shield and Saver.

A Transducer Shield® and Wedge assembled together will enable you to attach a transducer to a hull set back/step OR hole shot plate/baffle plate under a jack plate.  This wedge is NOT suitable for hole shot plates that are at a 90º angle with the transom.  For such jack plates, we recommend WG-2.5 Wedge or use an L Bracket to attach the Transducer Shield to the side of the jack plate.   If your transducer is a 10-1/4″ Lowrance® Structure Scan or Total Scan,  please go to Wedge Item # WG-LSS2.

When purchasing a wedge please choose and purchase a Transducer Shield®  for your transducer.  Click on Shields to make your choice by brand and transducer number.  Choose LWG-2 wedge for the following Transducer Shields:  Humminbird:  TM-HDSi Garmin:   TG-D-Vu    Lowrance:  TS-LSS-1, TS-HDI-2,  TS-HDI-3 and TS-HDI-4

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

Installing Your Transducer Correctly is Important

See More Fish    ……    Catch More Fish

The post LWG-2 Wedge for Hole Shot or Set Back install first appeared on Transducer Shield and Saver.

Choose WG-1 wedge for the following Transducer Shields:  Humminbird:  TM-CSI-2, TM-DI or TM-DI-2 and Lowrance:  TS-DSI

A Transducer Shield® and Wedge assembled together will enable you to attach a transducer to a hull set back or hole shot plate/baffle plate under a jack plate.  This wedge is NOT suitable for hole shot plates that are at a 90° angle with the transom, for example “Atlas”.  For such jack plates, we recommend WG-2.5 wedge or use an L Bracket and Transducer Shield combination to attach on the side of the jack plate.

It is very important that you complete the questionnaire when ordering this item.  The information you provide will help us to assist you better and avoid a delay in shipping your order.

Proudly Designed and Built in the USA

Installing your transducer correctly is Important

See More Fish ……..  Catch More Fish

The post WG-1 Wedge to attach a Transducer Shield to a Set Back or Hole Shot Plate first appeared on Transducer Shield and Saver.